view tests/test-push-checkheads-unpushed-D2.t @ 37054:40206e227412

wireproto: define and implement protocol for issuing requests

The existing HTTP and SSH wire protocols suffer from a host of flaws
and shortcomings. I've been wanting to rewrite the protocol for a while
now. Supporting partial clone - which will require new wire protocol
commands and capabilities - and other advanced server functionality
will be much easier if we start from a clean slate and don't have
to be constrained by limitations of the existing wire protocol.

This commit starts to introduce a new data exchange format for
use over the wire protocol.

The new protocol is built on top of "frames," which are atomic
units of metadata + data. Frames will make it easier to implement
proxies and other mechanisms that want to inspect data without
having to maintain state. The existing frame metadata is very
minimal and it will evolve heavily. (We will eventually support
things like concurrent requests, out-of-order responses,
compression, side-channels for status updates, etc. Some of
these will require additions to the frame header.)

Another benefit of frames is that all reads are of a fixed size.
A reader works by consuming a frame header, extracting the payload
length, then reading that many bytes. No lookahead, buffering, or
memory reallocations are needed.

The new protocol attempts to be transport agnostic. I want all that's
required to use the new protocol to be a pair of unidirectional,
half-duplex pipes. (Yes, we will eventually make use of full-duplex
pipes, but that's for another commit.) Notably, when the SSH
transport switches to this new protocol, stderr will be unused.
This is by design: the lack of stderr on HTTP harms protocol
behavior there. By shoehorning everything into a pair of pipes,
we can have more consistent behavior across transports.

We currently only define the client side parts of the new protocol,
specifically the bits for requesting that a command run. This keeps
the new code and feature small and somewhat easy to review.

We add support to `hg debugwireproto` for writing frames into
HTTP request bodies. Our tests that issue commands to the new
HTTP endpoint have been updated to transmit frames. The server
bits haven't been touched to consume the frames yet. This will
occur in the next commit...

Astute readers may notice that the command name is transmitted in
both the HTTP request URL and the command request frame. This is
partially a kludge from me initially implementing the frame-based
protocol for SSH first. But it is also a feature: I intend to
eventually support issuing multiple commands per HTTP request. This
will allow us to replace the abomination that is the "batch" wire
protocol command with a protocol-level mechanism for performing
multi-dispatch. Because I want the frame-based protocol to be
as similar as possible across transports, I'd rather we (redundantly)
include the command name in the frame than differ behavior between
transports that have out-of-band routing information (like HTTP)
readily available.

Differential Revision: https://phab.mercurial-scm.org/D2851

====================================
Testing head checking code: Case D-2
====================================

Mercurial checks for the introduction of new heads on push. Evolution comes
into play to detect if existing branches on the server are being replaced by
some of the new one we push.

This case is part of a series of tests checking this behavior.

Category D: remote head is "obs-affected" locally, but result is not part of the push
TestCase 1: remote branch has 2 changes, head is pruned, other is rewritten but result is not pushed

.. old-state:
..
.. * 1 changeset branch
..
.. new-state:
..
.. * old head is pruned
.. * 1 new branch succeeding to the other changeset in the old branch
.. * 1 new unrelated branch
..
.. expected-result:
..
.. * push allowed
.. * pushing only the unrelated branch: denied
..
.. graph-summary:
..
..   B ⊗
..     |
..   A ø⇠○ A'
..     |/
..     | ◔ C
..     |/
..     ●

  $ . $TESTDIR/testlib/push-checkheads-util.sh

Test setup
----------

  $ mkdir D2
  $ cd D2
  $ setuprepos
  creating basic server and client repo
  updating to branch default
  2 files updated, 0 files merged, 0 files removed, 0 files unresolved
  $ cd server
  $ mkcommit B0
  $ cd ../client
  $ hg pull
  pulling from $TESTTMP/D2/server
  searching for changes
  adding changesets
  adding manifests
  adding file changes
  added 1 changesets with 1 changes to 1 files
  new changesets d73caddc5533
  (run 'hg update' to get a working copy)
  $ hg up 0
  0 files updated, 0 files merged, 1 files removed, 0 files unresolved
  $ mkcommit A1
  created new head
  $ hg debugobsolete `getid "desc(A0)" ` `getid "desc(A1)"`
  obsoleted 1 changesets
  1 new orphan changesets
  $ hg debugobsolete --record-parents `getid "desc(B0)"`
  obsoleted 1 changesets
  $ hg up 0
  0 files updated, 0 files merged, 1 files removed, 0 files unresolved
  $ mkcommit C0
  created new head
  $ hg log -G --hidden
  @  0f88766e02d6 (draft): C0
  |
  | o  f6082bc4ffef (draft): A1
  |/
  | x  d73caddc5533 (draft): B0
  | |
  | x  8aaa48160adc (draft): A0
  |/
  o  1e4be0697311 (public): root
  

Actual testing
--------------

  $ hg push --rev 'desc(C0)'
  pushing to $TESTTMP/D2/server
  searching for changes
  abort: push creates new remote head 0f88766e02d6!
  (merge or see 'hg help push' for details about pushing new heads)
  [255]

  $ cd ../..