context: skip path conflicts by default when clearing unknown file (issue5776)
Prior to adding path conflict checking in 989e884d1be9, the test-audit-path.t
tests failed as shown here (but it was globbed away). 989e884d1be9 made it fail
with a message about the destination manifest containing a conflict (though the
no-symlink case wasn't updated). When the path conflict checking was gated
behind an experimental config in 2a774cae3a03^::2a774cae3a03, the update started
erroneously succeeding here. It turns out that the child of 989e884d1be9 is the
origin of this change when path conflict checking is disabled, as shown by
grafting the experimental config range on top of it.
What's happening here is merge.batchget() is writing the symlink 'back' to wdir
(but as a regular file for the no-symlink case), and then tries to write
'back/test', but calls wctx['back/test'].clearunknown() first. The code that's
gated here was removing the newly written 'back' file, allowing 'back/test' to
succeed. I tried checking for the dir components of 'back/test' in dirstate,
and skipping removal if present. But that didn't work because the dirstate
isn't updated after each file is written out.
This is the last persistent test failure on Windows, so the testbot should start
turning green now. \o/
============================================
Testing obsolescence markers push: Cases A.7
============================================
Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).
This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.
Category A: simple cases
TestCase 7: markers one non targeted common changeset
A.7 non targeted common changeset
=================================
.. {{{
.. ⇠◕ A
.. |
.. ● O
.. }}}
..
.. Markers exist from:
..
.. * Chain from A
..
.. Command run:
..
.. * hg push -r O
..
.. Expected exchange:
..
.. * ø
Setup
-----
$ . $TESTDIR/testlib/exchange-obsmarker-util.sh
Initial
$ setuprepos A.7
creating test repo for test case A.7
- pulldest
- main
- pushdest
cd into `main` and proceed with env setup
$ cd main
$ mkcommit A
$ hg push -q ../pushdest
$ hg push -q ../pulldest
$ hg debugobsolete aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa `getid 'desc(A)'`
$ hg log -G --hidden
@ f5bc6836db60 (draft): A
|
o a9bdc8b26820 (public): O
$ inspect_obsmarkers
obsstore content
================
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
$ cd ..
$ cd ..
Actual Test
-----------------------------------
$ dotest A.7 O
## Running testcase A.7
# testing echange of "O" (a9bdc8b26820)
## initial state
# obstore: main
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
# obstore: pushdest
# obstore: pulldest
## pushing "O" from main to pushdest
pushing to pushdest
searching for changes
no changes found
## post push state
# obstore: main
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
# obstore: pushdest
# obstore: pulldest
## pulling "a9bdc8b26820" from main into pulldest
pulling from main
no changes found
## post pull state
# obstore: main
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
# obstore: pushdest
# obstore: pulldest