annotate tests/test-debugcommands.t @ 25757:4d1382fd96ff

context: write dirstate out explicitly at the end of markcommitted

To detect change of a file without redundant comparison of file
content, dirstate recognizes a file as certainly clean, if:

  (1) it is already known as "normal",
  (2) dirstate entry for it has valid (= not "-1") timestamp, and
  (3) mode, size and timestamp of it on the filesystem are as same as
      ones expected in dirstate

This works as expected in many cases, but doesn't in the corner case
that changing a file keeps mode, size and timestamp of it on the
filesystem.

The timetable below shows steps in one of typical such situations:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N   ***
             (via 'repo.commit()')

         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              N    N      N

       - 'hg status' shows "r1" as "clean"   N    N      N
  ---- ----------------------------------- ---- ----- -----

The most important point is that 'dirstate.write()' is executed at N+1
or later. This causes writing dirstate timestamp N of "f" out
successfully. If it is executed at N, 'parsers.pack_dirstate()'
replaces timestamp N with "-1" before actual writing dirstate out.

This issue can occur when 'hg transplant' satisfies conditions below:

  - multiple revisions to be transplanted change the same file
  - those revisions don't change mode and size of the file, and
  - the 2nd or later revision of them fails after changing the file

The root cause of this issue is that files are changed without
flushing in-memory dirstate changes via 'repo.commit()' (even though
omitting 'dirstate.normallookup()' on files changed by 'patch.patch()'
for efficiency also causes this issue).

To detect changes of files correctly, this patch writes in-memory
dirstate changes out explicitly after marking files as clean in
'committablectx.markcommitted()', which is invoked via
'repo.commit()'.

After this change, timetable is changed as below:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N    ***
             (via 'repo.commit()')
       ----------------------------------- ---- ----- -----
           - 'dirsttate.write()'            -1    -1
       ----------------------------------- ---- ----- -----
         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              -1   -1     N

       - 'hg status' shows "r1" as "clean"   -1   -1     N
  ---- ----------------------------------- ---- ----- -----

To reproduce this issue in tests certainly, this patch emulates some
timing critical actions as below:

  - change "f" at N

    'patch.patch()' with 'fakepatchtime.py' explicitly changes mtime
    of patched files to "2000-01-01 00:00" (= N).

  - 'dirstate.write()' via 'repo.commit()' at N

    'fakedirstatewritetime.py' forces 'pack_dirstate()' to use
    "2000-01-01 00:00" as "now", only if 'pack_dirstate()' is invoked
    via 'committablectx.markcommitted()'.

  - 'dirstate.write()' via releasing wlock at N+1 (or "not at N")

    'pack_dirstate()' via releasing wlock uses actual timestamp at
    runtime as "now", and it should be different from the "2000-01-01
    00:00" of "f".

BTW, this patch doesn't test cases below, even though 'patch.patch()'
is used similarly in these cases:

  1. failure of 'hg import' or 'hg qpush'

  2. success of 'hg import', 'hg qpush' or 'hg transplant'

Case (1) above doesn't cause this kind of issue, because:

  - if patching is aborted by conflicts, changed files are committed

    changed files are marked as CLEAN, even though they are partially
    patched.

  - otherwise, dirstate are fully restored by 'dirstateguard'

    For example in timetable above, timestamp of "f" in .hg/dirstate
    is restored to -1 (or less than N), and subsequent 'hg status' can
    detect changes correctly.

Case (2) always causes 'repo.status()' invocation via 'repo.commit()'
just after changing files inside same wlock scope.

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
  N                                              ***   ***
       - make file "f" clean                            N

       - execute 'hg foobar'
         ....
         - 'dirstate.normal("f")'           N    ***
           (e.g. via dirty check
            or previous 'repo.commit()')

         - change "f", but keep size                    N
         - 'repo.status()' (*1)
           (via 'repo.commit()')
  ---- ----------------------------------- ---- ----- -----

At a glance, 'repo.status()' at (*1) seems to cause similar issue (=
"changed files are treated as clean"), but actually doesn't.

'dirstate._lastnormaltime' should be N at (*1) above, because
'dirstate.normal()' via dirty check is finished at N.

Therefore, "f" changed at N (= 'dirstate._lastnormaltime') is forcibly
treated as "unsure" at (*1), and changes are detected as expected (see
'dirstate.status()' for detail).

If 'hg import' is executed with '--no-commit', 'repo.status()' isn't
invoked just after changing files inside same wlock scope.

But preceding 'dirstate.normal()' is invoked inside another wlock
scope via 'cmdutil.bailifchanged()', and in-memory changes should be
flushed at the end of that scope.

Therefore, timestamp N of clean "f" should be replaced by -1, if
'dirstate.write()' is invoked at N. It means that condition of this
issue isn't satisfied.

  $ hg init debugrevlog
  $ cd debugrevlog
  $ echo a > a
  $ hg ci -Am adda
  adding a
  $ hg debugrevlog -m
  format : 1
  flags  : inline
  
  revisions     :  1
      merges    :  0 ( 0.00%)
      normal    :  1 (100.00%)
  revisions     :  1
      full      :  1 (100.00%)
      deltas    :  0 ( 0.00%)
  revision size : 44
      full      : 44 (100.00%)
      deltas    :  0 ( 0.00%)
  
  avg chain length  : 0
  max chain length  : 0
  compression ratio : 0
  
  uncompressed data size (min/max/avg) : 43 / 43 / 43
  full revision size (min/max/avg)     : 44 / 44 / 44
  delta size (min/max/avg)             : 0 / 0 / 0

Test debugindex, with and without the --debug flag
  $ hg debugindex a
     rev    offset  length   .... linkrev nodeid       p1           p2 (re)
       0         0       3   ....       0 b789fdd96dc2 000000000000 000000000000 (re)
  $ hg --debug debugindex a
     rev    offset  length   .... linkrev nodeid                                   p1                                       p2 (re)
       0         0       3   ....       0 b789fdd96dc2f3bd229c1dd8eedf0fc60e2b68e3 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 (re)
  $ hg debugindex -f 1 a
     rev flag   offset   length     size   ....   link     p1     p2       nodeid (re)
       0 0000        0        3        2   ....      0     -1     -1 b789fdd96dc2 (re)
  $ hg --debug debugindex -f 1 a
     rev flag   offset   length     size   ....   link     p1     p2                                   nodeid (re)
       0 0000        0        3        2   ....      0     -1     -1 b789fdd96dc2f3bd229c1dd8eedf0fc60e2b68e3 (re)


Test max chain len
  $ cat >> $HGRCPATH << EOF
  > [format]
  > maxchainlen=4
  > EOF

  $ printf "This test checks if maxchainlen config value is respected also it can serve as basic test for debugrevlog -d <file>.\n" >> a
  $ hg ci -m a
  $ printf "b\n" >> a
  $ hg ci -m a
  $ printf "c\n" >> a
  $ hg ci -m a
  $ printf "d\n" >> a
  $ hg ci -m a
  $ printf "e\n" >> a
  $ hg ci -m a
  $ printf "f\n" >> a
  $ hg ci -m a
  $ printf 'g\n' >> a
  $ hg ci -m a
  $ printf 'h\n' >> a
  $ hg ci -m a
  $ hg debugrevlog -d a
  # rev p1rev p2rev start   end deltastart base   p1   p2 rawsize totalsize compression heads chainlen
      0    -1    -1     0   ???          0    0    0    0     ???      ????           ?     1        0 (glob)
      1     0    -1   ???   ???          0    0    0    0     ???      ????           ?     1        1 (glob)
      2     1    -1   ???   ???        ???  ???  ???    0     ???      ????           ?     1        2 (glob)
      3     2    -1   ???   ???        ???  ???  ???    0     ???      ????           ?     1        3 (glob)
      4     3    -1   ???   ???        ???  ???  ???    0     ???      ????           ?     1        4 (glob)
      5     4    -1   ???   ???        ???  ???  ???    0     ???      ????           ?     1        0 (glob)
      6     5    -1   ???   ???        ???  ???  ???    0     ???      ????           ?     1        1 (glob)
      7     6    -1   ???   ???        ???  ???  ???    0     ???      ????           ?     1        2 (glob)
      8     7    -1   ???   ???        ???  ???  ???    0     ???      ????           ?     1        3 (glob)
  $ cd ..

Test internal debugstacktrace command

  $ cat > debugstacktrace.py << EOF
  > from mercurial.util import debugstacktrace, dst, sys
  > def f():
  >     dst('hello world')
  > def g():
  >     f()
  >     debugstacktrace(skip=-5, f=sys.stdout)
  > g()
  > EOF
  $ python debugstacktrace.py
  hello world at:
   debugstacktrace.py:7 in * (glob)
   debugstacktrace.py:5 in g
   debugstacktrace.py:3 in f
  stacktrace at:
   debugstacktrace.py:7 *in * (glob)
   debugstacktrace.py:6 *in g (glob)
   */util.py:* in debugstacktrace (glob)