annotate tests/test-addremove.t @ 23787:678f53865c68

revset: use localrepo revbranchcache for branch name filtering

Branch name filtering in revsets was expensive. For every rev it created a
changectx and called .branch() which retrieved the branch name from the
changelog.

Instead, use the revbranchcache.

The revbranchcache is used read-only. The revset implementation with generators
and callbacks makes it hard to figure out when we are done using/updating the
cache and could write it back. It would also be 'tricky' to lock the repo for
writing from within a revset execution. Finally, the branchmap update will
usually make sure that the cache is updated before any revset can be run.
The revbranchcache is used without any locking but is short-lived and used in a
tight loop where we can assume that the changelog doesn't change ... or where
it not is relevant to us if it does.

perfrevset 'branch(mobile)' on mozilla-central.
Before:
! wall 10.989637 comb 10.970000 user 10.940000 sys 0.030000 (best of 3)
After, no cache:
! wall 7.368656 comb 7.370000 user 7.360000 sys 0.010000 (best of 3)
After, with cache:
! wall 0.528098 comb 0.530000 user 0.530000 sys 0.000000 (best of 18)

The performance improvement even without cache come from being based on
branchinfo on the changelog instead of using ctx.branch().

Some tests are added to verify that the revbranchcache works and keep an eye on
when the cache files actually are updated.

  $ hg init rep
  $ cd rep
  $ mkdir dir
  $ touch foo dir/bar
  $ hg -v addremove
  adding dir/bar
  adding foo
  $ hg -v commit -m "add 1"
  committing files:
  dir/bar
  foo
  committing manifest
  committing changelog
  committed changeset 0:6f7f953567a2
  $ cd dir/
  $ touch ../foo_2 bar_2
  $ hg -v addremove
  adding dir/bar_2
  adding foo_2
  $ hg -v commit -m "add 2"
  committing files:
  dir/bar_2
  foo_2
  committing manifest
  committing changelog
  committed changeset 1:e65414bf35c5
  $ cd ..
  $ hg forget foo
  $ hg -v addremove
  adding foo
  $ hg forget foo
#if windows
  $ hg -v addremove nonexistant
  nonexistant: The system cannot find the file specified
  [1]
#else
  $ hg -v addremove nonexistant
  nonexistant: No such file or directory
  [1]
#endif
  $ cd ..

  $ hg init subdir
  $ cd subdir
  $ mkdir dir
  $ cd dir
  $ touch a.py
  $ hg addremove 'glob:*.py'
  adding a.py
  $ hg forget a.py
  $ hg addremove -I 'glob:*.py'
  adding a.py
  $ hg forget a.py
  $ hg addremove
  adding dir/a.py
  $ cd ..

  $ hg init sim
  $ cd sim
  $ echo a > a
  $ echo a >> a
  $ echo a >> a
  $ echo c > c
  $ hg commit -Ama
  adding a
  adding c
  $ mv a b
  $ rm c
  $ echo d > d
  $ hg addremove -n -s 50 # issue 1696
  removing a
  adding b
  removing c
  adding d
  recording removal of a as rename to b (100% similar)
  $ hg addremove -s 50
  removing a
  adding b
  removing c
  adding d
  recording removal of a as rename to b (100% similar)
  $ hg commit -mb
  $ cp b c
  $ hg forget b
  $ hg addremove -s 50
  adding b
  adding c

  $ rm c
#if windows
  $ hg ci -A -m "c" nonexistant
  nonexistant: The system cannot find the file specified
  abort: failed to mark all new/missing files as added/removed
  [255]
#else
  $ hg ci -A -m "c" nonexistant
  nonexistant: No such file or directory
  abort: failed to mark all new/missing files as added/removed
  [255]
#endif
  $ hg st
  ! c
  $ cd ..