annotate tests/test-exchange-obsmarkers-case-B7.t @ 33116:6c113a7dec52

tests: use the system hg for examining the local repository

Most test scripts use "hg" to interact with a temporary test repository.
However a few tests also want to run hg commands to interact with the local
repository containing the mercurial source code.  Notably, many of the
test-check-* tests want to check local files and commit messages.

These tests were previously using the version of hg being tested to query the
source repository.  However, this will fail if the source repository requires
extensions or other settings not supported by the version of mercurial being
tested.  The source repository was typically initially cloned using the system
hg installation, so we should use the system hg installation to query it.

There was already a helpers-testrepo.sh script designed to help cope with
different requirements for the source repository versus the test repositories.
However, it only handled the evolve extension.  This new behavior works with
any extensions that are different between the system installation and the test
installation.

============================================
Testing obsolescence markers push: Cases B.7
============================================

Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).

This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.

Category B: pruning case
TestCase 7: Prune on non-targeted common changeset

B.7 Prune above non-targeted common changeset
=============================================

.. (very similar to B1, but the prune changeset is unknown on remote)
..
.. {{{
..     ⊗ B
..     |
..     ◕ A
..     |
..     ● O
.. }}}
..
.. Marker exist from:
..
..  * B (prune)
..
.. Command runs:
..
..  * hg push -r O
..
.. Expected exclude:
..
..  * B (prune)

Setup
-----

  $ . $TESTDIR/testlib/exchange-obsmarker-util.sh

Initial

  $ setuprepos B.7
  creating test repo for test case B.7
  - pulldest
  - main
  - pushdest
  cd into `main` and proceed with env setup
  $ cd main
  $ mkcommit A
  $ hg push -q ../pushdest
  $ hg push -q ../pulldest
  $ mkcommit B
  $ hg prune -qd '0 0' .
  $ hg log -G --hidden
  x  f6fbb35d8ac9 (draft): B
  |
  @  f5bc6836db60 (draft): A
  |
  o  a9bdc8b26820 (public): O
  
  $ inspect_obsmarkers
  obsstore content
  ================
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  $ cd ..
  $ cd ..

Actual Test
-------------------------------------

  $ dotest B.7 O
  ## Running testcase B.7
  # testing echange of "O" (a9bdc8b26820)
  ## initial state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pushing "O" from main to pushdest
  pushing to pushdest
  searching for changes
  no changes found
  ## post push state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pulling "a9bdc8b26820" from main into pulldest
  pulling from main
  no changes found
  ## post pull state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest