annotate tests/test-exchange-obsmarkers-case-B1.t @ 33453:f6b7617a85bb

phases: add a 'registernew' method to set new phases

This new function will be used by code that adds new changesets. It ajusts the
phase boundary to make sure added changesets are at least in their target
phase (they end up in an higher phase if their parents are in a higher phase).

Having a dedicated function also simplify the phases tracking. All the new
nodes are passed as argument, so we know that all of them needs to have their
new phase registered. We also know that no other nodes will be affected, so no
extra computation are needed.

This function differ from 'retractboundary' where some nodes might change
phase while some other might not. It can also affect nodes not passed as
parameters.

These simplification also apply to the computation itself. For now we use
'_retractboundary' there by convenience, but we may introduces simpler code
later.

While registering new revisions, we still need to check the actual phases of
the added node because it might be higher than the target phase (eg: target is
draft but parent is secret).

We will migrate users over the next changesets.

============================================
Testing obsolescence markers push: Cases B.1
============================================

Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).

This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.

Category B: pruning case
TestCase 1: Prune on non-targeted common changeset

B.1 Prune on non-targeted common changeset
==========================================

.. {{{
..     ⊗ B
..     |
..     ◕ A
..     |
..     ● O
.. }}}
..
.. Marker exist from:
..
..  * B (prune)
..
.. Command runs:
..
..  * hg push -r O
..
.. Expected exclude:
..
..  * B (prune)

Setup
-----

  $ . $TESTDIR/testlib/exchange-obsmarker-util.sh

Initial

  $ setuprepos B.1
  creating test repo for test case B.1
  - pulldest
  - main
  - pushdest
  cd into `main` and proceed with env setup
  $ cd main
  $ mkcommit A
  $ mkcommit B

make both changeset known in remote

  $ hg push -qf ../pushdest
  $ hg push -qf ../pulldest

create prune marker

  $ hg prune -qd '0 0' .
  $ hg log -G --hidden
  x  f6fbb35d8ac9 (draft): B
  |
  @  f5bc6836db60 (draft): A
  |
  o  a9bdc8b26820 (public): O
  
  $ inspect_obsmarkers
  obsstore content
  ================
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  $ cd ..
  $ cd ..

Actual Test
-----------

  $ dotest B.1 O
  ## Running testcase B.1
  # testing echange of "O" (a9bdc8b26820)
  ## initial state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pushing "O" from main to pushdest
  pushing to pushdest
  searching for changes
  no changes found
  ## post push state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pulling "a9bdc8b26820" from main into pulldest
  pulling from main
  no changes found
  ## post pull state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest