view tests/test-exchange-obsmarkers-case-B1.t @ 41163:0101a35deae2

phabricator: warn if unable to amend, instead of aborting after posting

There was a divergence in behavior here between obsolete and strip based
amending.  I first noticed the abort when testing outside of the test harness,
but then had trouble recreating it here after reverting the code changes.  It
turns out, strip based amend was successfully amending the public commit after
it was posted!  It looks like the protection is in the `commit --amend` command,
not in the underlying code that it calls.

I considered doing a preflight check and aborting.  But the locks are only
acquired at the end, if amending, and this is too large a section of code to be
wrapped in a maybe-it's-held-or-not context manager for my tastes.
Additionally, some people do post-push reviews, and amending is the default
behavior, so they shouldn't see a misleading error message.

The lack of a 'Differential Revision' entry in the commit message breaks a
{phabreview} test, so it had to be partially conditionalized.

============================================
Testing obsolescence markers push: Cases B.1
============================================

Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).

This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.

Category B: pruning case
TestCase 1: Prune on non-targeted common changeset

B.1 Prune on non-targeted common changeset
==========================================

.. {{{
..     ⊗ B
..     |
..     ◕ A
..     |
..     ● O
.. }}}
..
.. Marker exist from:
..
..  * B (prune)
..
.. Command runs:
..
..  * hg push -r O
..
.. Expected exclude:
..
..  * B (prune)

Setup
-----

  $ . $TESTDIR/testlib/exchange-obsmarker-util.sh

Initial

  $ setuprepos B.1
  creating test repo for test case B.1
  - pulldest
  - main
  - pushdest
  cd into `main` and proceed with env setup
  $ cd main
  $ mkcommit A
  $ mkcommit B

make both changeset known in remote

  $ hg push -qf ../pushdest
  $ hg push -qf ../pulldest

create prune marker

  $ hg prune -qd '0 0' .
  $ hg log -G --hidden
  x  f6fbb35d8ac9 (draft): B
  |
  @  f5bc6836db60 (draft): A
  |
  o  a9bdc8b26820 (public): O
  
  $ inspect_obsmarkers
  obsstore content
  ================
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  $ cd ..
  $ cd ..

Actual Test
-----------

  $ dotest B.1 O
  ## Running testcase B.1
  # testing echange of "O" (a9bdc8b26820)
  ## initial state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pushing "O" from main to pushdest
  pushing to pushdest
  searching for changes
  no changes found
  ## post push state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pulling "a9bdc8b26820" from main into pulldest
  pulling from main
  no changes found
  ## post pull state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest