view tests/test-exchange-obsmarkers-case-B1.t @ 44985:1ca0047fd7e1

absorb: preserve changesets which were already empty Most commands in Mercurial (commit, rebase, absorb itself) don’t create empty changesets or drop them if they become empty. If there’s a changeset that’s empty, it must be a deliberate choice of the user. At least it shouldn’t be absorb’s responsibility to prune them. The fact that changesets that became empty during absorb are pruned, is unaffected by this. This case was found while writing patches which make it possible to configure absorb and rebase to not drop empty changesets. Even without having such config set, I think it’s valuable to preserve changesets which were already empty.
author Manuel Jacob <me@manueljacob.de>
date Mon, 01 Jun 2020 20:57:14 +0200
parents 850a06176d82
children
line wrap: on
line source

============================================
Testing obsolescence markers push: Cases B.1
============================================

Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).

This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.

Category B: pruning case
TestCase 1: Prune on non-targeted common changeset

B.1 Prune on non-targeted common changeset
==========================================

.. {{{
..     ⊗ B
..     |
..     ◕ A
..     |
..     ● O
.. }}}
..
.. Marker exist from:
..
..  * B (prune)
..
.. Command runs:
..
..  * hg push -r O
..
.. Expected exclude:
..
..  * B (prune)

Setup
-----

  $ . $TESTDIR/testlib/exchange-obsmarker-util.sh

Initial

  $ setuprepos B.1
  creating test repo for test case B.1
  - pulldest
  - main
  - pushdest
  cd into `main` and proceed with env setup
  $ cd main
  $ mkcommit A
  $ mkcommit B

make both changeset known in remote

  $ hg push -qf ../pushdest
  $ hg push -qf ../pulldest

create prune marker

  $ hg prune -qd '0 0' .
  $ hg log -G --hidden
  x  f6fbb35d8ac9 (draft): B
  |
  @  f5bc6836db60 (draft): A
  |
  o  a9bdc8b26820 (public): O
  
  $ inspect_obsmarkers
  obsstore content
  ================
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  $ cd ..
  $ cd ..

Actual Test
-----------

  $ dotest B.1 O
  ## Running testcase B.1
  # testing echange of "O" (a9bdc8b26820)
  ## initial state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pushing "O" from main to pushdest
  pushing to pushdest
  searching for changes
  no changes found
  ## post push state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pulling "a9bdc8b26820" from main into pulldest
  pulling from main
  no changes found
  ## post pull state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest