view tests/test-exchange-obsmarkers-case-A7.t @ 35449:24528dba0e64

run-tests: add substitution patterns for common '\' path output on Windows

The goal is to reduce the amount of hand tuning of new/changed tests that is
required on Windows.  Since the OS prints the proper paths everywhere else, this
is limited to Windows.  These are based on the check-code rules that were
dropped in 5feb782c7a95.

There are some minor tweaks, because those were trying to detect '/' paths
without a '(glob)' at the end, whereas these detect '\' paths. Also, it looks
like the 'no changes made to subrepo' one was broke, because the path to the
subrepo has been getting output but was not in the pattern.  End anchors are
dropped because '(glob)' is no longer required, but '(feature !)' annotations
are a possibility.

The 'saved backup bundle' pattern dropped from run-tests.py was simply carrying
over the first capture group.  The replace() method runs prior to evaluating
'\1', but it wasn't doing anything because of the 'r' prefix on '\\'.

The 'not recording move' entry is new, because I stumbled upon it searching for
some of these patterns.  There are probably others.

============================================
Testing obsolescence markers push: Cases A.7
============================================

Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).

This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.

Category A: simple cases
TestCase 7: markers one non targeted common changeset

A.7 non targeted common changeset
=================================

.. {{{
..    ⇠◕ A
..     |
..     ● O
.. }}}
..
.. Markers exist from:
..
..  * Chain from A
..
.. Command run:
..
..  * hg push -r O
..
.. Expected exchange:
..
..  * ø

Setup
-----

  $ . $TESTDIR/testlib/exchange-obsmarker-util.sh

Initial

  $ setuprepos A.7
  creating test repo for test case A.7
  - pulldest
  - main
  - pushdest
  cd into `main` and proceed with env setup
  $ cd main
  $ mkcommit A
  $ hg push -q ../pushdest
  $ hg push -q ../pulldest
  $ hg debugobsolete aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa `getid 'desc(A)'`
  $ hg log -G --hidden
  @  f5bc6836db60 (draft): A
  |
  o  a9bdc8b26820 (public): O
  
  $ inspect_obsmarkers
  obsstore content
  ================
  aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  $ cd ..
  $ cd ..

Actual Test
-----------------------------------

  $ dotest A.7 O
  ## Running testcase A.7
  # testing echange of "O" (a9bdc8b26820)
  ## initial state
  # obstore: main
  aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pushing "O" from main to pushdest
  pushing to pushdest
  searching for changes
  no changes found
  ## post push state
  # obstore: main
  aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pulling "a9bdc8b26820" from main into pulldest
  pulling from main
  no changes found
  ## post pull state
  # obstore: main
  aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa f5bc6836db60e308a17ba08bf050154ba9c4fad7 0 (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest