tests/sshprotoext.py

phases: large rewrite on retract boundary

The new code is still pure Python, so we still have room to going significantly
faster. However its complexity of the complex part is `O(|[min_new_draft, tip]|)` instead of
`O(|[min_draft, tip]|` which should help tremendously one repository with old
draft (like mercurial-devel or mozilla-try).

This is especially useful as the most common "retract boundary" operation
happens when we commit/rewrite new drafts or when we push new draft to a
non-publishing server. In this case, the smallest new_revs is very close to the
tip and there is very few work to do.

A few smaller optimisation could be done for these cases and will be introduced in
later changesets.

We still have iterate over large sets of roots, but this is already a great
improvement for a very small amount of work. We gather information on the
affected changeset as we go as we can put it to use in the next changesets.
This extra data collection might slowdown the `register_new` case a bit, however
for register_new, it should not really matters. The set of new nodes is either
small, so the impact is negligible, or the set of new nodes is large, and the
amount of work to do to had them will dominate the overhead the collecting
information in `changed_revs`.

As this new code compute the changes on the fly, it unlock other interesting
improvement to be done in later changeset.

# sshprotoext.py - Extension to test behavior of SSH protocol
#
# Copyright 2018 Gregory Szorc <[e-mail]>
#
# This software may be used and distributed according to the terms of the
# GNU General Public License version 2 or any later version.

# This extension replaces the SSH server started via `hg serve --stdio`.
# The server behaves differently depending on environment variables.


from mercurial import (
    error,
    extensions,
    registrar,
    sshpeer,
    wireprotoserver,
    wireprotov1server,
)

configtable = {}
configitem = registrar.configitem(configtable)

configitem(b'sshpeer', b'mode', default=None)
configitem(b'sshpeer', b'handshake-mode', default=None)


class bannerserver(wireprotoserver.sshserver):
    """Server that sends a banner to stdout."""

    def serve_forever(self):
        for i in range(10):
            self._fout.write(b'banner: line %d\n' % i)

        super(bannerserver, self).serve_forever()


class prehelloserver(wireprotoserver.sshserver):
    """Tests behavior when connecting to <0.9.1 servers.

    The ``hello`` wire protocol command was introduced in Mercurial
    0.9.1. Modern clients send the ``hello`` command when connecting
    to SSH servers. This mock server tests behavior of the handshake
    when ``hello`` is not supported.
    """

    def serve_forever(self):
        l = self._fin.readline()
        assert l == b'hello\n'
        # Respond to unknown commands with an empty reply.
        wireprotoserver._sshv1respondbytes(self._fout, b'')
        l = self._fin.readline()
        assert l == b'between\n'
        proto = wireprotoserver.sshv1protocolhandler(
            self._ui, self._fin, self._fout
        )
        rsp = wireprotov1server.dispatch(self._repo, proto, b'between')
        wireprotoserver._sshv1respondbytes(self._fout, rsp.data)

        super(prehelloserver, self).serve_forever()


def performhandshake(orig, ui, stdin, stdout, stderr):
    """Wrapped version of sshpeer._performhandshake to send extra commands."""
    mode = ui.config(b'sshpeer', b'handshake-mode')
    if mode == b'pre-no-args':
        ui.debug(b'sending no-args command\n')
        stdin.write(b'no-args\n')
        stdin.flush()
        return orig(ui, stdin, stdout, stderr)
    elif mode == b'pre-multiple-no-args':
        ui.debug(b'sending unknown1 command\n')
        stdin.write(b'unknown1\n')
        ui.debug(b'sending unknown2 command\n')
        stdin.write(b'unknown2\n')
        ui.debug(b'sending unknown3 command\n')
        stdin.write(b'unknown3\n')
        stdin.flush()
        return orig(ui, stdin, stdout, stderr)
    else:
        raise error.ProgrammingError(b'unknown HANDSHAKECOMMANDMODE: %s' % mode)


def extsetup(ui):
    # It's easier for tests to define the server behavior via environment
    # variables than config options. This is because `hg serve --stdio`
    # has to be invoked with a certain form for security reasons and
    # `dummyssh` can't just add `--config` flags to the command line.
    servermode = ui.environ.get(b'SSHSERVERMODE')

    if servermode == b'banner':
        wireprotoserver.sshserver = bannerserver
    elif servermode == b'no-hello':
        wireprotoserver.sshserver = prehelloserver
    elif servermode:
        raise error.ProgrammingError(b'unknown server mode: %s' % servermode)

    peermode = ui.config(b'sshpeer', b'mode')

    if peermode == b'extra-handshake-commands':
        extensions.wrapfunction(sshpeer, '_performhandshake', performhandshake)
    elif peermode:
        raise error.ProgrammingError(b'unknown peer mode: %s' % peermode)