Mercurial > hg
view tests/test-bookmarks-rebase.t @ 25757:4d1382fd96ff
context: write dirstate out explicitly at the end of markcommitted
To detect change of a file without redundant comparison of file
content, dirstate recognizes a file as certainly clean, if:
(1) it is already known as "normal",
(2) dirstate entry for it has valid (= not "-1") timestamp, and
(3) mode, size and timestamp of it on the filesystem are as same as
ones expected in dirstate
This works as expected in many cases, but doesn't in the corner case
that changing a file keeps mode, size and timestamp of it on the
filesystem.
The timetable below shows steps in one of typical such situations:
---- ----------------------------------- ----------------
timestamp of "f"
----------------
dirstate file-
time action mem file system
---- ----------------------------------- ---- ----- -----
* *** ***
- 'hg transplant REV1 REV2 ...'
- transplanting REV1
....
N
- change "f", but keep size N
(via 'patch.patch()')
- 'dirstate.normal("f")' N ***
(via 'repo.commit()')
- transplanting REV2
- change "f", but keep size N
(via 'patch.patch()')
- aborted while patching
N+1
- release wlock
- 'dirstate.write()' N N N
- 'hg status' shows "r1" as "clean" N N N
---- ----------------------------------- ---- ----- -----
The most important point is that 'dirstate.write()' is executed at N+1
or later. This causes writing dirstate timestamp N of "f" out
successfully. If it is executed at N, 'parsers.pack_dirstate()'
replaces timestamp N with "-1" before actual writing dirstate out.
This issue can occur when 'hg transplant' satisfies conditions below:
- multiple revisions to be transplanted change the same file
- those revisions don't change mode and size of the file, and
- the 2nd or later revision of them fails after changing the file
The root cause of this issue is that files are changed without
flushing in-memory dirstate changes via 'repo.commit()' (even though
omitting 'dirstate.normallookup()' on files changed by 'patch.patch()'
for efficiency also causes this issue).
To detect changes of files correctly, this patch writes in-memory
dirstate changes out explicitly after marking files as clean in
'committablectx.markcommitted()', which is invoked via
'repo.commit()'.
After this change, timetable is changed as below:
---- ----------------------------------- ----------------
timestamp of "f"
----------------
dirstate file-
time action mem file system
---- ----------------------------------- ---- ----- -----
* *** ***
- 'hg transplant REV1 REV2 ...'
- transplanting REV1
....
N
- change "f", but keep size N
(via 'patch.patch()')
- 'dirstate.normal("f")' N ***
(via 'repo.commit()')
----------------------------------- ---- ----- -----
- 'dirsttate.write()' -1 -1
----------------------------------- ---- ----- -----
- transplanting REV2
- change "f", but keep size N
(via 'patch.patch()')
- aborted while patching
N+1
- release wlock
- 'dirstate.write()' -1 -1 N
- 'hg status' shows "r1" as "clean" -1 -1 N
---- ----------------------------------- ---- ----- -----
To reproduce this issue in tests certainly, this patch emulates some
timing critical actions as below:
- change "f" at N
'patch.patch()' with 'fakepatchtime.py' explicitly changes mtime
of patched files to "2000-01-01 00:00" (= N).
- 'dirstate.write()' via 'repo.commit()' at N
'fakedirstatewritetime.py' forces 'pack_dirstate()' to use
"2000-01-01 00:00" as "now", only if 'pack_dirstate()' is invoked
via 'committablectx.markcommitted()'.
- 'dirstate.write()' via releasing wlock at N+1 (or "not at N")
'pack_dirstate()' via releasing wlock uses actual timestamp at
runtime as "now", and it should be different from the "2000-01-01
00:00" of "f".
BTW, this patch doesn't test cases below, even though 'patch.patch()'
is used similarly in these cases:
1. failure of 'hg import' or 'hg qpush'
2. success of 'hg import', 'hg qpush' or 'hg transplant'
Case (1) above doesn't cause this kind of issue, because:
- if patching is aborted by conflicts, changed files are committed
changed files are marked as CLEAN, even though they are partially
patched.
- otherwise, dirstate are fully restored by 'dirstateguard'
For example in timetable above, timestamp of "f" in .hg/dirstate
is restored to -1 (or less than N), and subsequent 'hg status' can
detect changes correctly.
Case (2) always causes 'repo.status()' invocation via 'repo.commit()'
just after changing files inside same wlock scope.
---- ----------------------------------- ----------------
timestamp of "f"
----------------
dirstate file-
time action mem file system
---- ----------------------------------- ---- ----- -----
N *** ***
- make file "f" clean N
- execute 'hg foobar'
....
- 'dirstate.normal("f")' N ***
(e.g. via dirty check
or previous 'repo.commit()')
- change "f", but keep size N
- 'repo.status()' (*1)
(via 'repo.commit()')
---- ----------------------------------- ---- ----- -----
At a glance, 'repo.status()' at (*1) seems to cause similar issue (=
"changed files are treated as clean"), but actually doesn't.
'dirstate._lastnormaltime' should be N at (*1) above, because
'dirstate.normal()' via dirty check is finished at N.
Therefore, "f" changed at N (= 'dirstate._lastnormaltime') is forcibly
treated as "unsure" at (*1), and changes are detected as expected (see
'dirstate.status()' for detail).
If 'hg import' is executed with '--no-commit', 'repo.status()' isn't
invoked just after changing files inside same wlock scope.
But preceding 'dirstate.normal()' is invoked inside another wlock
scope via 'cmdutil.bailifchanged()', and in-memory changes should be
flushed at the end of that scope.
Therefore, timestamp N of clean "f" should be replaced by -1, if
'dirstate.write()' is invoked at N. It means that condition of this
issue isn't satisfied.
author | FUJIWARA Katsunori <foozy@lares.dti.ne.jp> |
---|---|
date | Wed, 08 Jul 2015 17:01:09 +0900 |
parents | 91c2278c68a3 |
children | ef1eb6df7071 |
line wrap: on
line source
$ echo "[extensions]" >> $HGRCPATH $ echo "rebase=" >> $HGRCPATH initialize repository $ hg init $ echo 'a' > a $ hg ci -A -m "0" adding a $ echo 'b' > b $ hg ci -A -m "1" adding b $ hg up 0 0 files updated, 0 files merged, 1 files removed, 0 files unresolved $ echo 'c' > c $ hg ci -A -m "2" adding c created new head $ echo 'd' > d $ hg ci -A -m "3" adding d $ hg bookmark -r 1 one $ hg bookmark -r 3 two $ hg up -q two bookmark list $ hg bookmark one 1:925d80f479bb * two 3:2ae46b1d99a7 rebase $ hg rebase -s two -d one rebasing 3:2ae46b1d99a7 "3" (tip two) saved backup bundle to $TESTTMP/.hg/strip-backup/2ae46b1d99a7-e6b057bc-backup.hg (glob) $ hg log changeset: 3:42e5ed2cdcf4 bookmark: two tag: tip parent: 1:925d80f479bb user: test date: Thu Jan 01 00:00:00 1970 +0000 summary: 3 changeset: 2:db815d6d32e6 parent: 0:f7b1eb17ad24 user: test date: Thu Jan 01 00:00:00 1970 +0000 summary: 2 changeset: 1:925d80f479bb bookmark: one user: test date: Thu Jan 01 00:00:00 1970 +0000 summary: 1 changeset: 0:f7b1eb17ad24 user: test date: Thu Jan 01 00:00:00 1970 +0000 summary: 0 aborted rebase should restore active bookmark. $ hg up 1 0 files updated, 0 files merged, 1 files removed, 0 files unresolved (leaving bookmark two) $ echo 'e' > d $ hg ci -A -m "4" adding d created new head $ hg bookmark three $ hg rebase -s three -d two rebasing 4:dd7c838e8362 "4" (tip three) merging d warning: conflicts during merge. merging d incomplete! (edit conflicts, then use 'hg resolve --mark') unresolved conflicts (see hg resolve, then hg rebase --continue) [1] $ hg rebase --abort rebase aborted $ hg bookmark one 1:925d80f479bb * three 4:dd7c838e8362 two 3:42e5ed2cdcf4 after aborted rebase, restoring a bookmark that has been removed should not fail $ hg rebase -s three -d two rebasing 4:dd7c838e8362 "4" (tip three) merging d warning: conflicts during merge. merging d incomplete! (edit conflicts, then use 'hg resolve --mark') unresolved conflicts (see hg resolve, then hg rebase --continue) [1] $ hg bookmark -d three $ hg rebase --abort rebase aborted $ hg bookmark one 1:925d80f479bb two 3:42e5ed2cdcf4