view tests/test-import-merge.t @ 25757:4d1382fd96ff

context: write dirstate out explicitly at the end of markcommitted

To detect change of a file without redundant comparison of file
content, dirstate recognizes a file as certainly clean, if:

  (1) it is already known as "normal",
  (2) dirstate entry for it has valid (= not "-1") timestamp, and
  (3) mode, size and timestamp of it on the filesystem are as same as
      ones expected in dirstate

This works as expected in many cases, but doesn't in the corner case
that changing a file keeps mode, size and timestamp of it on the
filesystem.

The timetable below shows steps in one of typical such situations:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N   ***
             (via 'repo.commit()')

         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              N    N      N

       - 'hg status' shows "r1" as "clean"   N    N      N
  ---- ----------------------------------- ---- ----- -----

The most important point is that 'dirstate.write()' is executed at N+1
or later. This causes writing dirstate timestamp N of "f" out
successfully. If it is executed at N, 'parsers.pack_dirstate()'
replaces timestamp N with "-1" before actual writing dirstate out.

This issue can occur when 'hg transplant' satisfies conditions below:

  - multiple revisions to be transplanted change the same file
  - those revisions don't change mode and size of the file, and
  - the 2nd or later revision of them fails after changing the file

The root cause of this issue is that files are changed without
flushing in-memory dirstate changes via 'repo.commit()' (even though
omitting 'dirstate.normallookup()' on files changed by 'patch.patch()'
for efficiency also causes this issue).

To detect changes of files correctly, this patch writes in-memory
dirstate changes out explicitly after marking files as clean in
'committablectx.markcommitted()', which is invoked via
'repo.commit()'.

After this change, timetable is changed as below:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N    ***
             (via 'repo.commit()')
       ----------------------------------- ---- ----- -----
           - 'dirsttate.write()'            -1    -1
       ----------------------------------- ---- ----- -----
         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              -1   -1     N

       - 'hg status' shows "r1" as "clean"   -1   -1     N
  ---- ----------------------------------- ---- ----- -----

To reproduce this issue in tests certainly, this patch emulates some
timing critical actions as below:

  - change "f" at N

    'patch.patch()' with 'fakepatchtime.py' explicitly changes mtime
    of patched files to "2000-01-01 00:00" (= N).

  - 'dirstate.write()' via 'repo.commit()' at N

    'fakedirstatewritetime.py' forces 'pack_dirstate()' to use
    "2000-01-01 00:00" as "now", only if 'pack_dirstate()' is invoked
    via 'committablectx.markcommitted()'.

  - 'dirstate.write()' via releasing wlock at N+1 (or "not at N")

    'pack_dirstate()' via releasing wlock uses actual timestamp at
    runtime as "now", and it should be different from the "2000-01-01
    00:00" of "f".

BTW, this patch doesn't test cases below, even though 'patch.patch()'
is used similarly in these cases:

  1. failure of 'hg import' or 'hg qpush'

  2. success of 'hg import', 'hg qpush' or 'hg transplant'

Case (1) above doesn't cause this kind of issue, because:

  - if patching is aborted by conflicts, changed files are committed

    changed files are marked as CLEAN, even though they are partially
    patched.

  - otherwise, dirstate are fully restored by 'dirstateguard'

    For example in timetable above, timestamp of "f" in .hg/dirstate
    is restored to -1 (or less than N), and subsequent 'hg status' can
    detect changes correctly.

Case (2) always causes 'repo.status()' invocation via 'repo.commit()'
just after changing files inside same wlock scope.

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
  N                                              ***   ***
       - make file "f" clean                            N

       - execute 'hg foobar'
         ....
         - 'dirstate.normal("f")'           N    ***
           (e.g. via dirty check
            or previous 'repo.commit()')

         - change "f", but keep size                    N
         - 'repo.status()' (*1)
           (via 'repo.commit()')
  ---- ----------------------------------- ---- ----- -----

At a glance, 'repo.status()' at (*1) seems to cause similar issue (=
"changed files are treated as clean"), but actually doesn't.

'dirstate._lastnormaltime' should be N at (*1) above, because
'dirstate.normal()' via dirty check is finished at N.

Therefore, "f" changed at N (= 'dirstate._lastnormaltime') is forcibly
treated as "unsure" at (*1), and changes are detected as expected (see
'dirstate.status()' for detail).

If 'hg import' is executed with '--no-commit', 'repo.status()' isn't
invoked just after changing files inside same wlock scope.

But preceding 'dirstate.normal()' is invoked inside another wlock
scope via 'cmdutil.bailifchanged()', and in-memory changes should be
flushed at the end of that scope.

Therefore, timestamp N of clean "f" should be replaced by -1, if
'dirstate.write()' is invoked at N. It means that condition of this
issue isn't satisfied.

  $ echo "[extensions]" >> $HGRCPATH
  $ echo "mq=" >> $HGRCPATH

  $ tipparents() {
  > hg parents --template "{rev}:{node|short} {desc|firstline}\n" -r tip
  > }

Test import and merge diffs

  $ hg init repo
  $ cd repo
  $ echo a > a
  $ hg ci -Am adda
  adding a
  $ echo a >> a
  $ hg ci -m changea
  $ echo c > c
  $ hg ci -Am addc
  adding c
  $ hg up 0
  1 files updated, 0 files merged, 1 files removed, 0 files unresolved
  $ echo b > b
  $ hg ci -Am addb
  adding b
  created new head
  $ hg up 1
  1 files updated, 0 files merged, 1 files removed, 0 files unresolved
  $ hg merge 3
  1 files updated, 0 files merged, 0 files removed, 0 files unresolved
  (branch merge, don't forget to commit)
  $ hg ci -m merge
  $ hg export . > ../merge.diff
  $ grep -v '^merge$' ../merge.diff > ../merge.nomsg.diff
  $ cd ..
  $ hg clone -r2 repo repo2
  adding changesets
  adding manifests
  adding file changes
  added 3 changesets with 3 changes to 2 files
  updating to branch default
  2 files updated, 0 files merged, 0 files removed, 0 files unresolved
  $ cd repo2
  $ hg pull -r3 ../repo
  pulling from ../repo
  searching for changes
  adding changesets
  adding manifests
  adding file changes
  added 1 changesets with 1 changes to 1 files (+1 heads)
  (run 'hg heads' to see heads, 'hg merge' to merge)

Test without --exact and diff.p1 == workingdir.p1

  $ hg up 1
  0 files updated, 0 files merged, 1 files removed, 0 files unresolved
  $ cat > $TESTTMP/editor.sh <<EOF
  > env | grep HGEDITFORM
  > echo merge > \$1
  > EOF
  $ HGEDITOR="sh $TESTTMP/editor.sh" hg import --edit ../merge.nomsg.diff
  applying ../merge.nomsg.diff
  HGEDITFORM=import.normal.merge
  $ tipparents
  1:540395c44225 changea
  3:102a90ea7b4a addb
  $ hg strip --no-backup tip
  0 files updated, 0 files merged, 1 files removed, 0 files unresolved

Test without --exact and diff.p1 != workingdir.p1

  $ hg up 2
  1 files updated, 0 files merged, 0 files removed, 0 files unresolved
  $ hg import ../merge.diff
  applying ../merge.diff
  warning: import the patch as a normal revision
  (use --exact to import the patch as a merge)
  $ tipparents
  2:890ecaa90481 addc
  $ hg strip --no-backup tip
  0 files updated, 0 files merged, 1 files removed, 0 files unresolved

Test with --exact

  $ hg import --exact ../merge.diff
  applying ../merge.diff
  0 files updated, 0 files merged, 1 files removed, 0 files unresolved
  $ tipparents
  1:540395c44225 changea
  3:102a90ea7b4a addb
  $ hg strip --no-backup tip
  0 files updated, 0 files merged, 1 files removed, 0 files unresolved

Test with --bypass and diff.p1 == workingdir.p1

  $ hg up 1
  0 files updated, 0 files merged, 0 files removed, 0 files unresolved
  $ hg import --bypass ../merge.diff
  applying ../merge.diff
  $ tipparents
  1:540395c44225 changea
  3:102a90ea7b4a addb
  $ hg strip --no-backup tip

Test with --bypass and diff.p1 != workingdir.p1

  $ hg up 2
  1 files updated, 0 files merged, 0 files removed, 0 files unresolved
  $ hg import --bypass ../merge.diff
  applying ../merge.diff
  warning: import the patch as a normal revision
  (use --exact to import the patch as a merge)
  $ tipparents
  2:890ecaa90481 addc
  $ hg strip --no-backup tip

Test with --bypass and --exact

  $ hg import --bypass --exact ../merge.diff
  applying ../merge.diff
  $ tipparents
  1:540395c44225 changea
  3:102a90ea7b4a addb
  $ hg strip --no-backup tip

  $ cd ..

Test that --exact on a bad header doesn't corrupt the repo (issue3616)

  $ hg init repo3
  $ cd repo3
  $ echo a>a
  $ hg ci -Aqm0
  $ echo a>>a
  $ hg ci -m1
  $ echo a>>a
  $ hg ci -m2
  $ echo a>a
  $ echo b>>a
  $ echo a>>a
  $ hg ci -m3
  $ hg export 2 | head -7 > ../a.patch
  $ hg export tip > out
  >>> apatch = open("../a.patch", "ab")
  >>> apatch.write("".join(open("out").readlines()[7:]))

  $ cd ..
  $ hg clone -qr0 repo3 repo3-clone
  $ cd repo3-clone
  $ hg pull -qr1 ../repo3

  $ hg import --exact ../a.patch
  applying ../a.patch
  1 files updated, 0 files merged, 0 files removed, 0 files unresolved
  patching file a
  Hunk #1 succeeded at 1 with fuzz 1 (offset -1 lines).
  transaction abort!
  rollback completed
  abort: patch is damaged or loses information
  [255]
  $ hg verify
  checking changesets
  checking manifests
  crosschecking files in changesets and manifests
  checking files
  1 files, 2 changesets, 2 total revisions