view tests/test-module-imports.t @ 25757:4d1382fd96ff

context: write dirstate out explicitly at the end of markcommitted

To detect change of a file without redundant comparison of file
content, dirstate recognizes a file as certainly clean, if:

  (1) it is already known as "normal",
  (2) dirstate entry for it has valid (= not "-1") timestamp, and
  (3) mode, size and timestamp of it on the filesystem are as same as
      ones expected in dirstate

This works as expected in many cases, but doesn't in the corner case
that changing a file keeps mode, size and timestamp of it on the
filesystem.

The timetable below shows steps in one of typical such situations:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N   ***
             (via 'repo.commit()')

         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              N    N      N

       - 'hg status' shows "r1" as "clean"   N    N      N
  ---- ----------------------------------- ---- ----- -----

The most important point is that 'dirstate.write()' is executed at N+1
or later. This causes writing dirstate timestamp N of "f" out
successfully. If it is executed at N, 'parsers.pack_dirstate()'
replaces timestamp N with "-1" before actual writing dirstate out.

This issue can occur when 'hg transplant' satisfies conditions below:

  - multiple revisions to be transplanted change the same file
  - those revisions don't change mode and size of the file, and
  - the 2nd or later revision of them fails after changing the file

The root cause of this issue is that files are changed without
flushing in-memory dirstate changes via 'repo.commit()' (even though
omitting 'dirstate.normallookup()' on files changed by 'patch.patch()'
for efficiency also causes this issue).

To detect changes of files correctly, this patch writes in-memory
dirstate changes out explicitly after marking files as clean in
'committablectx.markcommitted()', which is invoked via
'repo.commit()'.

After this change, timetable is changed as below:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N    ***
             (via 'repo.commit()')
       ----------------------------------- ---- ----- -----
           - 'dirsttate.write()'            -1    -1
       ----------------------------------- ---- ----- -----
         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              -1   -1     N

       - 'hg status' shows "r1" as "clean"   -1   -1     N
  ---- ----------------------------------- ---- ----- -----

To reproduce this issue in tests certainly, this patch emulates some
timing critical actions as below:

  - change "f" at N

    'patch.patch()' with 'fakepatchtime.py' explicitly changes mtime
    of patched files to "2000-01-01 00:00" (= N).

  - 'dirstate.write()' via 'repo.commit()' at N

    'fakedirstatewritetime.py' forces 'pack_dirstate()' to use
    "2000-01-01 00:00" as "now", only if 'pack_dirstate()' is invoked
    via 'committablectx.markcommitted()'.

  - 'dirstate.write()' via releasing wlock at N+1 (or "not at N")

    'pack_dirstate()' via releasing wlock uses actual timestamp at
    runtime as "now", and it should be different from the "2000-01-01
    00:00" of "f".

BTW, this patch doesn't test cases below, even though 'patch.patch()'
is used similarly in these cases:

  1. failure of 'hg import' or 'hg qpush'

  2. success of 'hg import', 'hg qpush' or 'hg transplant'

Case (1) above doesn't cause this kind of issue, because:

  - if patching is aborted by conflicts, changed files are committed

    changed files are marked as CLEAN, even though they are partially
    patched.

  - otherwise, dirstate are fully restored by 'dirstateguard'

    For example in timetable above, timestamp of "f" in .hg/dirstate
    is restored to -1 (or less than N), and subsequent 'hg status' can
    detect changes correctly.

Case (2) always causes 'repo.status()' invocation via 'repo.commit()'
just after changing files inside same wlock scope.

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
  N                                              ***   ***
       - make file "f" clean                            N

       - execute 'hg foobar'
         ....
         - 'dirstate.normal("f")'           N    ***
           (e.g. via dirty check
            or previous 'repo.commit()')

         - change "f", but keep size                    N
         - 'repo.status()' (*1)
           (via 'repo.commit()')
  ---- ----------------------------------- ---- ----- -----

At a glance, 'repo.status()' at (*1) seems to cause similar issue (=
"changed files are treated as clean"), but actually doesn't.

'dirstate._lastnormaltime' should be N at (*1) above, because
'dirstate.normal()' via dirty check is finished at N.

Therefore, "f" changed at N (= 'dirstate._lastnormaltime') is forcibly
treated as "unsure" at (*1), and changes are detected as expected (see
'dirstate.status()' for detail).

If 'hg import' is executed with '--no-commit', 'repo.status()' isn't
invoked just after changing files inside same wlock scope.

But preceding 'dirstate.normal()' is invoked inside another wlock
scope via 'cmdutil.bailifchanged()', and in-memory changes should be
flushed at the end of that scope.

Therefore, timestamp N of clean "f" should be replaced by -1, if
'dirstate.write()' is invoked at N. It means that condition of this
issue isn't satisfied.

#require test-repo

  $ import_checker="$TESTDIR"/../contrib/import-checker.py

Run the doctests from the import checker, and make sure
it's working correctly.
  $ TERM=dumb
  $ export TERM
  $ python -m doctest $import_checker

Run additional tests for the import checker

  $ mkdir testpackage

  $ cat > testpackage/multiple.py << EOF
  > from __future__ import absolute_import
  > import os, sys
  > EOF

  $ cat > testpackage/unsorted.py << EOF
  > from __future__ import absolute_import
  > import sys
  > import os
  > EOF

  $ cat > testpackage/stdafterlocal.py << EOF
  > from __future__ import absolute_import
  > from . import unsorted
  > import os
  > EOF

  $ cat > testpackage/requirerelative.py << EOF
  > from __future__ import absolute_import
  > import testpackage.unsorted
  > EOF

  $ cat > testpackage/importalias.py << EOF
  > from __future__ import absolute_import
  > import ui
  > EOF

  $ cat > testpackage/relativestdlib.py << EOF
  > from __future__ import absolute_import
  > from .. import os
  > EOF

  $ cat > testpackage/symbolimport.py << EOF
  > from __future__ import absolute_import
  > from .unsorted import foo
  > EOF

  $ cat > testpackage/latesymbolimport.py << EOF
  > from __future__ import absolute_import
  > from . import unsorted
  > from mercurial.node import hex
  > EOF

  $ cat > testpackage/multiplegroups.py << EOF
  > from __future__ import absolute_import
  > from . import unsorted
  > from . import more
  > EOF

  $ mkdir testpackage/subpackage
  $ cat > testpackage/subpackage/levelpriority.py << EOF
  > from __future__ import absolute_import
  > from . import foo
  > from .. import parent
  > EOF

  $ cat > testpackage/sortedentries.py << EOF
  > from __future__ import absolute_import
  > from . import (
  >     foo,
  >     bar,
  > )
  > EOF

  $ cat > testpackage/importfromalias.py << EOF
  > from __future__ import absolute_import
  > from . import ui
  > EOF

  $ cat > testpackage/importfromrelative.py << EOF
  > from __future__ import absolute_import
  > from testpackage.unsorted import foo
  > EOF

  $ python "$import_checker" testpackage/*.py testpackage/subpackage/*.py
  testpackage/importalias.py ui module must be "as" aliased to uimod
  testpackage/importfromalias.py ui from testpackage must be "as" aliased to uimod
  testpackage/importfromrelative.py import should be relative: testpackage.unsorted
  testpackage/importfromrelative.py direct symbol import from testpackage.unsorted
  testpackage/latesymbolimport.py symbol import follows non-symbol import: mercurial.node
  testpackage/multiple.py multiple imported names: os, sys
  testpackage/multiplegroups.py multiple "from . import" statements
  testpackage/relativestdlib.py relative import of stdlib module
  testpackage/requirerelative.py import should be relative: testpackage.unsorted
  testpackage/sortedentries.py imports from testpackage not lexically sorted: bar < foo
  testpackage/stdafterlocal.py stdlib import follows local import: os
  testpackage/subpackage/levelpriority.py higher-level import should come first: testpackage
  testpackage/symbolimport.py direct symbol import from testpackage.unsorted
  testpackage/unsorted.py imports not lexically sorted: os < sys
  [1]

  $ cd "$TESTDIR"/..

There are a handful of cases here that require renaming a module so it
doesn't overlap with a stdlib module name. There are also some cycles
here that we should still endeavor to fix, and some cycles will be
hidden by deduplication algorithm in the cycle detector, so fixing
these may expose other cycles.

  $ hg locate 'mercurial/**.py' 'hgext/**.py' | sed 's-\\-/-g' | python "$import_checker" -
  mercurial/dispatch.py mixed imports
     stdlib:    commands
     relative:  error, extensions, fancyopts, hg, hook, util
  mercurial/fileset.py mixed imports
     stdlib:    parser
     relative:  error, merge, util
  mercurial/revset.py mixed imports
     stdlib:    parser
     relative:  error, hbisect, phases, util
  mercurial/templater.py mixed imports
     stdlib:    parser
     relative:  config, error, templatefilters, templatekw, util
  mercurial/ui.py mixed imports
     stdlib:    formatter
     relative:  config, error, progress, scmutil, util
  Import cycle: mercurial.cmdutil -> mercurial.context -> mercurial.subrepo -> mercurial.cmdutil
  Import cycle: hgext.largefiles.basestore -> hgext.largefiles.localstore -> hgext.largefiles.basestore
  Import cycle: mercurial.commands -> mercurial.commandserver -> mercurial.dispatch -> mercurial.commands
  [1]