view tests/test-status.t @ 25757:4d1382fd96ff

context: write dirstate out explicitly at the end of markcommitted

To detect change of a file without redundant comparison of file
content, dirstate recognizes a file as certainly clean, if:

  (1) it is already known as "normal",
  (2) dirstate entry for it has valid (= not "-1") timestamp, and
  (3) mode, size and timestamp of it on the filesystem are as same as
      ones expected in dirstate

This works as expected in many cases, but doesn't in the corner case
that changing a file keeps mode, size and timestamp of it on the
filesystem.

The timetable below shows steps in one of typical such situations:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N   ***
             (via 'repo.commit()')

         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              N    N      N

       - 'hg status' shows "r1" as "clean"   N    N      N
  ---- ----------------------------------- ---- ----- -----

The most important point is that 'dirstate.write()' is executed at N+1
or later. This causes writing dirstate timestamp N of "f" out
successfully. If it is executed at N, 'parsers.pack_dirstate()'
replaces timestamp N with "-1" before actual writing dirstate out.

This issue can occur when 'hg transplant' satisfies conditions below:

  - multiple revisions to be transplanted change the same file
  - those revisions don't change mode and size of the file, and
  - the 2nd or later revision of them fails after changing the file

The root cause of this issue is that files are changed without
flushing in-memory dirstate changes via 'repo.commit()' (even though
omitting 'dirstate.normallookup()' on files changed by 'patch.patch()'
for efficiency also causes this issue).

To detect changes of files correctly, this patch writes in-memory
dirstate changes out explicitly after marking files as clean in
'committablectx.markcommitted()', which is invoked via
'repo.commit()'.

After this change, timetable is changed as below:

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
   *                                             ***    ***
       - 'hg transplant REV1 REV2 ...'
         - transplanting REV1
           ....
   N
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - 'dirstate.normal("f")'          N    ***
             (via 'repo.commit()')
       ----------------------------------- ---- ----- -----
           - 'dirsttate.write()'            -1    -1
       ----------------------------------- ---- ----- -----
         - transplanting REV2
           - change "f", but keep size                   N
             (via 'patch.patch()')
           - aborted while patching
  N+1
         - release wlock
           - 'dirstate.write()'              -1   -1     N

       - 'hg status' shows "r1" as "clean"   -1   -1     N
  ---- ----------------------------------- ---- ----- -----

To reproduce this issue in tests certainly, this patch emulates some
timing critical actions as below:

  - change "f" at N

    'patch.patch()' with 'fakepatchtime.py' explicitly changes mtime
    of patched files to "2000-01-01 00:00" (= N).

  - 'dirstate.write()' via 'repo.commit()' at N

    'fakedirstatewritetime.py' forces 'pack_dirstate()' to use
    "2000-01-01 00:00" as "now", only if 'pack_dirstate()' is invoked
    via 'committablectx.markcommitted()'.

  - 'dirstate.write()' via releasing wlock at N+1 (or "not at N")

    'pack_dirstate()' via releasing wlock uses actual timestamp at
    runtime as "now", and it should be different from the "2000-01-01
    00:00" of "f".

BTW, this patch doesn't test cases below, even though 'patch.patch()'
is used similarly in these cases:

  1. failure of 'hg import' or 'hg qpush'

  2. success of 'hg import', 'hg qpush' or 'hg transplant'

Case (1) above doesn't cause this kind of issue, because:

  - if patching is aborted by conflicts, changed files are committed

    changed files are marked as CLEAN, even though they are partially
    patched.

  - otherwise, dirstate are fully restored by 'dirstateguard'

    For example in timetable above, timestamp of "f" in .hg/dirstate
    is restored to -1 (or less than N), and subsequent 'hg status' can
    detect changes correctly.

Case (2) always causes 'repo.status()' invocation via 'repo.commit()'
just after changing files inside same wlock scope.

  ---- ----------------------------------- ----------------
                                           timestamp of "f"
                                           ----------------
                                           dirstate   file-
  time          action                     mem  file  system
  ---- ----------------------------------- ---- ----- -----
  N                                              ***   ***
       - make file "f" clean                            N

       - execute 'hg foobar'
         ....
         - 'dirstate.normal("f")'           N    ***
           (e.g. via dirty check
            or previous 'repo.commit()')

         - change "f", but keep size                    N
         - 'repo.status()' (*1)
           (via 'repo.commit()')
  ---- ----------------------------------- ---- ----- -----

At a glance, 'repo.status()' at (*1) seems to cause similar issue (=
"changed files are treated as clean"), but actually doesn't.

'dirstate._lastnormaltime' should be N at (*1) above, because
'dirstate.normal()' via dirty check is finished at N.

Therefore, "f" changed at N (= 'dirstate._lastnormaltime') is forcibly
treated as "unsure" at (*1), and changes are detected as expected (see
'dirstate.status()' for detail).

If 'hg import' is executed with '--no-commit', 'repo.status()' isn't
invoked just after changing files inside same wlock scope.

But preceding 'dirstate.normal()' is invoked inside another wlock
scope via 'cmdutil.bailifchanged()', and in-memory changes should be
flushed at the end of that scope.

Therefore, timestamp N of clean "f" should be replaced by -1, if
'dirstate.write()' is invoked at N. It means that condition of this
issue isn't satisfied.

  $ hg init repo1
  $ cd repo1
  $ mkdir a b a/1 b/1 b/2
  $ touch in_root a/in_a b/in_b a/1/in_a_1 b/1/in_b_1 b/2/in_b_2

hg status in repo root:

  $ hg status
  ? a/1/in_a_1
  ? a/in_a
  ? b/1/in_b_1
  ? b/2/in_b_2
  ? b/in_b
  ? in_root

hg status . in repo root:

  $ hg status .
  ? a/1/in_a_1
  ? a/in_a
  ? b/1/in_b_1
  ? b/2/in_b_2
  ? b/in_b
  ? in_root

  $ hg status --cwd a
  ? a/1/in_a_1
  ? a/in_a
  ? b/1/in_b_1
  ? b/2/in_b_2
  ? b/in_b
  ? in_root
  $ hg status --cwd a .
  ? 1/in_a_1
  ? in_a
  $ hg status --cwd a ..
  ? 1/in_a_1
  ? in_a
  ? ../b/1/in_b_1
  ? ../b/2/in_b_2
  ? ../b/in_b
  ? ../in_root

  $ hg status --cwd b
  ? a/1/in_a_1
  ? a/in_a
  ? b/1/in_b_1
  ? b/2/in_b_2
  ? b/in_b
  ? in_root
  $ hg status --cwd b .
  ? 1/in_b_1
  ? 2/in_b_2
  ? in_b
  $ hg status --cwd b ..
  ? ../a/1/in_a_1
  ? ../a/in_a
  ? 1/in_b_1
  ? 2/in_b_2
  ? in_b
  ? ../in_root

  $ hg status --cwd a/1
  ? a/1/in_a_1
  ? a/in_a
  ? b/1/in_b_1
  ? b/2/in_b_2
  ? b/in_b
  ? in_root
  $ hg status --cwd a/1 .
  ? in_a_1
  $ hg status --cwd a/1 ..
  ? in_a_1
  ? ../in_a

  $ hg status --cwd b/1
  ? a/1/in_a_1
  ? a/in_a
  ? b/1/in_b_1
  ? b/2/in_b_2
  ? b/in_b
  ? in_root
  $ hg status --cwd b/1 .
  ? in_b_1
  $ hg status --cwd b/1 ..
  ? in_b_1
  ? ../2/in_b_2
  ? ../in_b

  $ hg status --cwd b/2
  ? a/1/in_a_1
  ? a/in_a
  ? b/1/in_b_1
  ? b/2/in_b_2
  ? b/in_b
  ? in_root
  $ hg status --cwd b/2 .
  ? in_b_2
  $ hg status --cwd b/2 ..
  ? ../1/in_b_1
  ? in_b_2
  ? ../in_b

combining patterns with root and patterns without a root works

  $ hg st a/in_a re:.*b$
  ? a/in_a
  ? b/in_b

  $ cd ..

  $ hg init repo2
  $ cd repo2
  $ touch modified removed deleted ignored
  $ echo "^ignored$" > .hgignore
  $ hg ci -A -m 'initial checkin'
  adding .hgignore
  adding deleted
  adding modified
  adding removed
  $ touch modified added unknown ignored
  $ hg add added
  $ hg remove removed
  $ rm deleted

hg status:

  $ hg status
  A added
  R removed
  ! deleted
  ? unknown

hg status modified added removed deleted unknown never-existed ignored:

  $ hg status modified added removed deleted unknown never-existed ignored
  never-existed: * (glob)
  A added
  R removed
  ! deleted
  ? unknown

  $ hg copy modified copied

hg status -C:

  $ hg status -C
  A added
  A copied
    modified
  R removed
  ! deleted
  ? unknown

hg status -A:

  $ hg status -A
  A added
  A copied
    modified
  R removed
  ! deleted
  ? unknown
  I ignored
  C .hgignore
  C modified

  $ hg status -A -Tjson
  [
   {
    "path": "added",
    "status": "A"
   },
   {
    "copy": "modified",
    "path": "copied",
    "status": "A"
   },
   {
    "path": "removed",
    "status": "R"
   },
   {
    "path": "deleted",
    "status": "!"
   },
   {
    "path": "unknown",
    "status": "?"
   },
   {
    "path": "ignored",
    "status": "I"
   },
   {
    "path": ".hgignore",
    "status": "C"
   },
   {
    "path": "modified",
    "status": "C"
   }
  ]

  $ hg status -A -Tpickle > pickle
  >>> import pickle
  >>> print sorted((x['status'], x['path']) for x in pickle.load(open("pickle")))
  [('!', 'deleted'), ('?', 'pickle'), ('?', 'unknown'), ('A', 'added'), ('A', 'copied'), ('C', '.hgignore'), ('C', 'modified'), ('I', 'ignored'), ('R', 'removed')]
  $ rm pickle

  $ echo "^ignoreddir$" > .hgignore
  $ mkdir ignoreddir
  $ touch ignoreddir/file

Test templater support:

  $ hg status -AT "[{status}]\t{if(copy, '{copy} -> ')}{path}\n"
  [M]	.hgignore
  [A]	added
  [A]	modified -> copied
  [R]	removed
  [!]	deleted
  [?]	ignored
  [?]	unknown
  [I]	ignoreddir/file
  [C]	modified
  $ hg status -AT default
  M .hgignore
  A added
  A copied
    modified
  R removed
  ! deleted
  ? ignored
  ? unknown
  I ignoreddir/file
  C modified
  $ hg status -T compact
  abort: "status" not in template map
  [255]

hg status ignoreddir/file:

  $ hg status ignoreddir/file

hg status -i ignoreddir/file:

  $ hg status -i ignoreddir/file
  I ignoreddir/file
  $ cd ..

Check 'status -q' and some combinations

  $ hg init repo3
  $ cd repo3
  $ touch modified removed deleted ignored
  $ echo "^ignored$" > .hgignore
  $ hg commit -A -m 'initial checkin'
  adding .hgignore
  adding deleted
  adding modified
  adding removed
  $ touch added unknown ignored
  $ hg add added
  $ echo "test" >> modified
  $ hg remove removed
  $ rm deleted
  $ hg copy modified copied

Specify working directory revision explicitly, that should be the same as
"hg status"

  $ hg status --change "wdir()"
  M modified
  A added
  A copied
  R removed
  ! deleted
  ? unknown

Run status with 2 different flags.
Check if result is the same or different.
If result is not as expected, raise error

  $ assert() {
  >     hg status $1 > ../a
  >     hg status $2 > ../b
  >     if diff ../a ../b > /dev/null; then
  >         out=0
  >     else
  >         out=1
  >     fi
  >     if [ $3 -eq 0 ]; then
  >         df="same"
  >     else
  >         df="different"
  >     fi
  >     if [ $out -ne $3 ]; then
  >         echo "Error on $1 and $2, should be $df."
  >     fi
  > }

Assert flag1 flag2 [0-same | 1-different]

  $ assert "-q" "-mard"      0
  $ assert "-A" "-marduicC"  0
  $ assert "-qA" "-mardcC"   0
  $ assert "-qAui" "-A"      0
  $ assert "-qAu" "-marducC" 0
  $ assert "-qAi" "-mardicC" 0
  $ assert "-qu" "-u"        0
  $ assert "-q" "-u"         1
  $ assert "-m" "-a"         1
  $ assert "-r" "-d"         1
  $ cd ..

  $ hg init repo4
  $ cd repo4
  $ touch modified removed deleted
  $ hg ci -q -A -m 'initial checkin'
  $ touch added unknown
  $ hg add added
  $ hg remove removed
  $ rm deleted
  $ echo x > modified
  $ hg copy modified copied
  $ hg ci -m 'test checkin' -d "1000001 0"
  $ rm *
  $ touch unrelated
  $ hg ci -q -A -m 'unrelated checkin' -d "1000002 0"

hg status --change 1:

  $ hg status --change 1
  M modified
  A added
  A copied
  R removed

hg status --change 1 unrelated:

  $ hg status --change 1 unrelated

hg status -C --change 1 added modified copied removed deleted:

  $ hg status -C --change 1 added modified copied removed deleted
  M modified
  A added
  A copied
    modified
  R removed

hg status -A --change 1 and revset:

  $ hg status -A --change '1|1'
  M modified
  A added
  A copied
    modified
  R removed
  C deleted

  $ cd ..

hg status of binary file starting with '\1\n', a separator for metadata:

  $ hg init repo5
  $ cd repo5
  >>> open("010a", "wb").write("\1\nfoo")
  $ hg ci -q -A -m 'initial checkin'
  $ hg status -A
  C 010a

  >>> open("010a", "wb").write("\1\nbar")
  $ hg status -A
  M 010a
  $ hg ci -q -m 'modify 010a'
  $ hg status -A --rev 0:1
  M 010a

  $ touch empty
  $ hg ci -q -A -m 'add another file'
  $ hg status -A --rev 1:2 010a
  C 010a

  $ cd ..

test "hg status" with "directory pattern" which matches against files
only known on target revision.

  $ hg init repo6
  $ cd repo6

  $ echo a > a.txt
  $ hg add a.txt
  $ hg commit -m '#0'
  $ mkdir -p 1/2/3/4/5
  $ echo b > 1/2/3/4/5/b.txt
  $ hg add 1/2/3/4/5/b.txt
  $ hg commit -m '#1'

  $ hg update -C 0 > /dev/null
  $ hg status -A
  C a.txt

the directory matching against specified pattern should be removed,
because directory existence prevents 'dirstate.walk()' from showing
warning message about such pattern.

  $ test ! -d 1
  $ hg status -A --rev 1 1/2/3/4/5/b.txt
  R 1/2/3/4/5/b.txt
  $ hg status -A --rev 1 1/2/3/4/5
  R 1/2/3/4/5/b.txt
  $ hg status -A --rev 1 1/2/3
  R 1/2/3/4/5/b.txt
  $ hg status -A --rev 1 1
  R 1/2/3/4/5/b.txt

  $ hg status --config ui.formatdebug=True --rev 1 1
  status = [
      {*'path': '1/2/3/4/5/b.txt'*}, (glob)
  ]

#if windows
  $ hg --config ui.slash=false status -A --rev 1 1
  R 1\2\3\4\5\b.txt
#endif

  $ cd ..

Status after move overwriting a file (issue4458)
=================================================


  $ hg init issue4458
  $ cd issue4458
  $ echo a > a
  $ echo b > b
  $ hg commit -Am base
  adding a
  adding b


with --force

  $ hg mv b --force a
  $ hg st --copies
  M a
    b
  R b
  $ hg revert --all
  reverting a
  undeleting b
  $ rm *.orig

without force

  $ hg rm a
  $ hg st --copies
  R a
  $ hg mv b a
  $ hg st --copies
  M a
    b
  R b

using ui.statuscopies setting
  $ hg st --config ui.statuscopies=true
  M a
    b
  R b
  $ hg st --config ui.statuscopies=false
  M a
  R b

Other "bug" highlight, the revision status does not report the copy information.
This is buggy behavior.

  $ hg commit -m 'blah'
  $ hg st --copies --change .
  M a
  R b

  $ cd ..