notify: add debug output. do not fail if no config file.
use --debug to see debug output.
HGRC(5)
=======
Bryan O'Sullivan <bos@serpentine.com>
NAME
----
hgrc - configuration files for Mercurial
SYNOPSIS
--------
The Mercurial system uses a set of configuration files to control
aspects of its behaviour.
FILES
-----
Mercurial reads configuration data from several files, if they exist.
The names of these files depend on the system on which Mercurial is
installed.
(Unix) <install-root>/etc/mercurial/hgrc.d/*.rc::
(Unix) <install-root>/etc/mercurial/hgrc::
Per-installation configuration files, searched for in the
directory where Mercurial is installed. For example, if installed
in /shared/tools, Mercurial will look in
/shared/tools/etc/mercurial/hgrc. Options in these files apply to
all Mercurial commands executed by any user in any directory.
(Unix) /etc/mercurial/hgrc.d/*.rc::
(Unix) /etc/mercurial/hgrc::
(Windows) C:\Mercurial\Mercurial.ini::
Per-system configuration files, for the system on which Mercurial
is running. Options in these files apply to all Mercurial
commands executed by any user in any directory. Options in these
files override per-installation options.
(Unix) $HOME/.hgrc::
(Windows) C:\Documents and Settings\USERNAME\Mercurial.ini::
(Windows) $HOME\Mercurial.ini::
Per-user configuration file, for the user running Mercurial.
Options in this file apply to all Mercurial commands executed by
any user in any directory. Options in this file override
per-installation and per-system options.
On Windows system, one of these is chosen exclusively according
to definition of HOME environment variable.
(Unix, Windows) <repo>/.hg/hgrc::
Per-repository configuration options that only apply in a
particular repository. This file is not version-controlled, and
will not get transferred during a "clone" operation. Options in
this file override options in all other configuration files.
SYNTAX
------
A configuration file consists of sections, led by a "[section]" header
and followed by "name: value" entries; "name=value" is also accepted.
[spam]
eggs=ham
green=
eggs
Each line contains one entry. If the lines that follow are indented,
they are treated as continuations of that entry.
Leading whitespace is removed from values. Empty lines are skipped.
The optional values can contain format strings which refer to other
values in the same section, or values in a special DEFAULT section.
Lines beginning with "#" or ";" are ignored and may be used to provide
comments.
SECTIONS
--------
This section describes the different sections that may appear in a
Mercurial "hgrc" file, the purpose of each section, its possible
keys, and their possible values.
decode/encode::
Filters for transforming files on checkout/checkin. This would
typically be used for newline processing or other
localization/canonicalization of files.
Filters consist of a filter pattern followed by a filter command.
Filter patterns are globs by default, rooted at the repository
root. For example, to match any file ending in ".txt" in the root
directory only, use the pattern "*.txt". To match any file ending
in ".c" anywhere in the repository, use the pattern "**.c".
The filter command can start with a specifier, either "pipe:" or
"tempfile:". If no specifier is given, "pipe:" is used by default.
A "pipe:" command must accept data on stdin and return the
transformed data on stdout.
Pipe example:
[encode]
# uncompress gzip files on checkin to improve delta compression
# note: not necessarily a good idea, just an example
*.gz = pipe: gunzip
[decode]
# recompress gzip files when writing them to the working dir (we
# can safely omit "pipe:", because it's the default)
*.gz = gzip
A "tempfile:" command is a template. The string INFILE is replaced
with the name of a temporary file that contains the data to be
filtered by the command. The string OUTFILE is replaced with the
name of an empty temporary file, where the filtered data must be
written by the command.
NOTE: the tempfile mechanism is recommended for Windows systems,
where the standard shell I/O redirection operators often have
strange effects. In particular, if you are doing line ending
conversion on Windows using the popular dos2unix and unix2dos
programs, you *must* use the tempfile mechanism, as using pipes will
corrupt the contents of your files.
Tempfile example:
[encode]
# convert files to unix line ending conventions on checkin
**.txt = tempfile: dos2unix -n INFILE OUTFILE
[decode]
# convert files to windows line ending conventions when writing
# them to the working dir
**.txt = tempfile: unix2dos -n INFILE OUTFILE
email::
Settings for extensions that send email messages.
from;;
Optional. Email address to use in "From" header and SMTP envelope
of outgoing messages.
method;;
Optional. Method to use to send email messages. If value is
"smtp" (default), use SMTP (see section "[mail]" for
configuration). Otherwise, use as name of program to run that
acts like sendmail (takes "-f" option for sender, list of
recipients on command line, message on stdin). Normally, setting
this to "sendmail" or "/usr/sbin/sendmail" is enough to use
sendmail to send messages.
Email example:
[email]
from = Joseph User <joe.user@example.com>
method = /usr/sbin/sendmail
extensions::
Mercurial has an extension mechanism for adding new features. To
enable an extension, create an entry for it in this section.
If you know that the extension is already in Python's search path,
you can give the name of the module, followed by "=", with nothing
after the "=".
Otherwise, give a name that you choose, followed by "=", followed by
the path to the ".py" file (including the file name extension) that
defines the extension.
hooks::
Commands or Python functions that get automatically executed by
various actions such as starting or finishing a commit. Multiple
hooks can be run for the same action by appending a suffix to the
action. Overriding a site-wide hook can be done by changing its
value or setting it to an empty string.
Example .hg/hgrc:
[hooks]
# do not use the site-wide hook
incoming =
incoming.email = /my/email/hook
incoming.autobuild = /my/build/hook
Most hooks are run with environment variables set that give added
useful information. For each hook below, the environment variables
it is passed are listed with names of the form "$HG_foo".
changegroup;;
Run after a changegroup has been added via push, pull or
unbundle. ID of the first new changeset is in $HG_NODE.
commit;;
Run after a changeset has been created in the local repository.
ID of the newly created changeset is in $HG_NODE. Parent
changeset IDs are in $HG_PARENT1 and $HG_PARENT2.
incoming;;
Run after a changeset has been pulled, pushed, or unbundled into
the local repository. The ID of the newly arrived changeset is in
$HG_NODE.
outgoing;;
Run after sending changes from local repository to another. ID of
first changeset sent is in $HG_NODE. Source of operation is in
$HG_SOURCE; see "preoutgoing" hook for description.
prechangegroup;;
Run before a changegroup is added via push, pull or unbundle.
Exit status 0 allows the changegroup to proceed. Non-zero status
will cause the push, pull or unbundle to fail.
precommit;;
Run before starting a local commit. Exit status 0 allows the
commit to proceed. Non-zero status will cause the commit to fail.
Parent changeset IDs are in $HG_PARENT1 and $HG_PARENT2.
preoutgoing;;
Run before computing changes to send from the local repository to
another. Non-zero status will cause failure. This lets you
prevent pull over http or ssh. Also prevents against local pull,
push (outbound) or bundle commands, but not effective, since you
can just copy files instead then. Source of operation is in
$HG_SOURCE. If "serve", operation is happening on behalf of
remote ssh or http repository. If "push", "pull" or "bundle",
operation is happening on behalf of repository on same system.
pretag;;
Run before creating a tag. Exit status 0 allows the tag to be
created. Non-zero status will cause the tag to fail. ID of
changeset to tag is in $HG_NODE. Name of tag is in $HG_TAG. Tag
is local if $HG_LOCAL=1, in repo if $HG_LOCAL=0.
pretxnchangegroup;;
Run after a changegroup has been added via push, pull or unbundle,
but before the transaction has been committed. Changegroup is
visible to hook program. This lets you validate incoming changes
before accepting them. Passed the ID of the first new changeset
in $HG_NODE. Exit status 0 allows the transaction to commit.
Non-zero status will cause the transaction to be rolled back and
the push, pull or unbundle will fail.
pretxncommit;;
Run after a changeset has been created but the transaction not yet
committed. Changeset is visible to hook program. This lets you
validate commit message and changes. Exit status 0 allows the
commit to proceed. Non-zero status will cause the transaction to
be rolled back. ID of changeset is in $HG_NODE. Parent changeset
IDs are in $HG_PARENT1 and $HG_PARENT2.
preupdate;;
Run before updating the working directory. Exit status 0 allows
the update to proceed. Non-zero status will prevent the update.
Changeset ID of first new parent is in $HG_PARENT1. If merge, ID
of second new parent is in $HG_PARENT2.
tag;;
Run after a tag is created. ID of tagged changeset is in
$HG_NODE. Name of tag is in $HG_TAG. Tag is local if
$HG_LOCAL=1, in repo if $HG_LOCAL=0.
update;;
Run after updating the working directory. Changeset ID of first
new parent is in $HG_PARENT1. If merge, ID of second new parent
is in $HG_PARENT2. If update succeeded, $HG_ERROR=0. If update
failed (e.g. because conflicts not resolved), $HG_ERROR=1.
Note: In earlier releases, the names of hook environment variables
did not have a "HG_" prefix. The old unprefixed names are no longer
provided in the environment.
The syntax for Python hooks is as follows:
hookname = python:modulename.submodule.callable
Python hooks are run within the Mercurial process. Each hook is
called with at least three keyword arguments: a ui object (keyword
"ui"), a repository object (keyword "repo"), and a "hooktype"
keyword that tells what kind of hook is used. Arguments listed as
environment variables above are passed as keyword arguments, with no
"HG_" prefix, and names in lower case.
A Python hook must return a "true" value to succeed. Returning a
"false" value or raising an exception is treated as failure of the
hook.
http_proxy::
Used to access web-based Mercurial repositories through a HTTP
proxy.
host;;
Host name and (optional) port of the proxy server, for example
"myproxy:8000".
no;;
Optional. Comma-separated list of host names that should bypass
the proxy.
passwd;;
Optional. Password to authenticate with at the proxy server.
user;;
Optional. User name to authenticate with at the proxy server.
smtp::
Configuration for extensions that need to send email messages.
host;;
Optional. Host name of mail server. Default: "mail".
port;;
Optional. Port to connect to on mail server. Default: 25.
tls;;
Optional. Whether to connect to mail server using TLS. True or
False. Default: False.
username;;
Optional. User name to authenticate to SMTP server with.
If username is specified, password must also be specified.
Default: none.
password;;
Optional. Password to authenticate to SMTP server with.
If username is specified, password must also be specified.
Default: none.
paths::
Assigns symbolic names to repositories. The left side is the
symbolic name, and the right gives the directory or URL that is the
location of the repository. Default paths can be declared by
setting the following entries.
default;;
Directory or URL to use when pulling if no source is specified.
Default is set to repository from which the current repository
was cloned.
default-push;;
Optional. Directory or URL to use when pushing if no destination
is specified.
ui::
User interface controls.
debug;;
Print debugging information. True or False. Default is False.
editor;;
The editor to use during a commit. Default is $EDITOR or "vi".
ignore;;
A file to read per-user ignore patterns from. This file should be in
the same format as a repository-wide .hgignore file. This option
supports hook syntax, so if you want to specify multiple ignore
files, you can do so by setting something like
"ignore.other = ~/.hgignore2". For details of the ignore file
format, see the hgignore(5) man page.
interactive;;
Allow to prompt the user. True or False. Default is True.
logtemplate;;
Template string for commands that print changesets.
style;;
Name of style to use for command output.
merge;;
The conflict resolution program to use during a manual merge.
Default is "hgmerge".
quiet;;
Reduce the amount of output printed. True or False. Default is False.
remotecmd;;
remote command to use for clone/push/pull operations. Default is 'hg'.
ssh;;
command to use for SSH connections. Default is 'ssh'.
timeout;;
The timeout used when a lock is held (in seconds), a negative value
means no timeout. Default is 600.
username;;
The committer of a changeset created when running "commit".
Typically a person's name and email address, e.g. "Fred Widget
<fred@example.com>". Default is $EMAIL or username@hostname, unless
username is set to an empty string, which enforces specifying the
username manually.
verbose;;
Increase the amount of output printed. True or False. Default is False.
web::
Web interface configuration.
accesslog;;
Where to output the access log. Default is stdout.
address;;
Interface address to bind to. Default is all.
allowbz2;;
Whether to allow .tar.bz2 downloading of repo revisions. Default is false.
allowgz;;
Whether to allow .tar.gz downloading of repo revisions. Default is false.
allowpull;;
Whether to allow pulling from the repository. Default is true.
allowzip;;
Whether to allow .zip downloading of repo revisions. Default is false.
This feature creates temporary files.
baseurl;;
Base URL to use when publishing URLs in other locations, so
third-party tools like email notification hooks can construct URLs.
Example: "http://hgserver/repos/"
description;;
Textual description of the repository's purpose or contents.
Default is "unknown".
errorlog;;
Where to output the error log. Default is stderr.
ipv6;;
Whether to use IPv6. Default is false.
name;;
Repository name to use in the web interface. Default is current
working directory.
maxchanges;;
Maximum number of changes to list on the changelog. Default is 10.
maxfiles;;
Maximum number of files to list per changeset. Default is 10.
port;;
Port to listen on. Default is 8000.
style;;
Which template map style to use.
templates;;
Where to find the HTML templates. Default is install path.
AUTHOR
------
Bryan O'Sullivan <bos@serpentine.com>.
Mercurial was written by Matt Mackall <mpm@selenic.com>.
SEE ALSO
--------
hg(1), hgignore(5)
COPYING
-------
This manual page is copyright 2005 Bryan O'Sullivan.
Mercurial is copyright 2005, 2006 Matt Mackall.
Free use of this software is granted under the terms of the GNU General
Public License (GPL).