view tests/test-exchange-obsmarkers-case-B7.t @ 41247:a89b20a49c13

rust-cpython: using MissingAncestors from Python code

As precedently done with LazyAncestors on cpython.rs, we test for the
presence of the 'rustext' module.

incrementalmissingrevs() has two callers within the Mercurial core:
`setdiscovery.partialdiscovery` and the `only()` revset.

This move shows a significant discovery performance improvement
in cases where the baseline is slow: using perfdiscovery on the PyPy
repos, prepared with `contrib/discovery-helper <repo> 50 100`, we
get averaged medians of 403ms with the Rust version vs 742ms without
(about 45% better).

But there are still indications that performance can be worse in cases
the baseline is fast, possibly due to the conversion from Python to
Rust and back becoming the bottleneck. We could measure this on
mozilla-central in cases were the delta is just a few changesets.
This requires confirmation, but if that's the reason, then an
upcoming `partialdiscovery` fully in Rust should solve the problem.

Differential Revision: https://phab.mercurial-scm.org/D5551

============================================
Testing obsolescence markers push: Cases B.7
============================================

Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).

This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.

Category B: pruning case
TestCase 7: Prune on non-targeted common changeset

B.7 Prune above non-targeted common changeset
=============================================

.. (very similar to B1, but the prune changeset is unknown on remote)
..
.. {{{
..     ⊗ B
..     |
..     ◕ A
..     |
..     ● O
.. }}}
..
.. Marker exist from:
..
..  * B (prune)
..
.. Command runs:
..
..  * hg push -r O
..
.. Expected exclude:
..
..  * B (prune)

Setup
-----

  $ . $TESTDIR/testlib/exchange-obsmarker-util.sh

Initial

  $ setuprepos B.7
  creating test repo for test case B.7
  - pulldest
  - main
  - pushdest
  cd into `main` and proceed with env setup
  $ cd main
  $ mkcommit A
  $ hg push -q ../pushdest
  $ hg push -q ../pulldest
  $ mkcommit B
  $ hg prune -qd '0 0' .
  $ hg log -G --hidden
  x  f6fbb35d8ac9 (draft): B
  |
  @  f5bc6836db60 (draft): A
  |
  o  a9bdc8b26820 (public): O
  
  $ inspect_obsmarkers
  obsstore content
  ================
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  $ cd ..
  $ cd ..

Actual Test
-------------------------------------

  $ dotest B.7 O
  ## Running testcase B.7
  # testing echange of "O" (a9bdc8b26820)
  ## initial state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pushing "O" from main to pushdest
  pushing to pushdest
  searching for changes
  no changes found
  ## post push state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pulling "a9bdc8b26820" from main into pulldest
  pulling from main
  no changes found
  ## post pull state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest