tests/test-config.t

shelve: move possible shelve file extensions to a single place

This and a couple of following patches are a preparation to
implementing obsolescense-enabled shelve which was discussed
on a Sprint. If this refactoring is not done, shelve is going
to look even more hackish than now.

This particular commit introduces a slight behavior change. Previously,
if only .hg/shelve/name.patch file exists, but .hg/name.hg does not,
'hg shelve -d name' would fail saying "shelve not found". Now deletion
will only fail if .patch file does not exist (since .patch is used
as an indicator of an existing shelve). Other shelve files being absent
are skipped silently to accommodate for future introduction of obs-based
shelve, which will mean that for some shelves .hg and .patch files exist,
while for others .hg and .oshelve.

hide outer repo
  $ hg init

Invalid syntax: no value

  $ cat > .hg/hgrc << EOF
  > novaluekey
  > EOF
  $ hg showconfig
  hg: parse error at $TESTTMP/.hg/hgrc:1: novaluekey (glob)
  [255]

Invalid syntax: no key

  $ cat > .hg/hgrc << EOF
  > =nokeyvalue
  > EOF
  $ hg showconfig
  hg: parse error at $TESTTMP/.hg/hgrc:1: =nokeyvalue (glob)
  [255]

Test hint about invalid syntax from leading white space

  $ cat > .hg/hgrc << EOF
  >  key=value
  > EOF
  $ hg showconfig
  hg: parse error at $TESTTMP/.hg/hgrc:1:  key=value (glob)
  unexpected leading whitespace
  [255]

  $ cat > .hg/hgrc << EOF
  >  [section]
  > key=value
  > EOF
  $ hg showconfig
  hg: parse error at $TESTTMP/.hg/hgrc:1:  [section] (glob)
  unexpected leading whitespace
  [255]

Reset hgrc

  $ echo > .hg/hgrc

Test case sensitive configuration

  $ cat <<EOF >> $HGRCPATH
  > [Section]
  > KeY = Case Sensitive
  > key = lower case
  > EOF

  $ hg showconfig Section
  Section.KeY=Case Sensitive
  Section.key=lower case

  $ hg showconfig Section -Tjson
  [
   {
    "name": "Section.KeY",
    "source": "*.hgrc:16", (glob)
    "value": "Case Sensitive"
   },
   {
    "name": "Section.key",
    "source": "*.hgrc:17", (glob)
    "value": "lower case"
   }
  ]
  $ hg showconfig Section.KeY -Tjson
  [
   {
    "name": "Section.KeY",
    "source": "*.hgrc:16", (glob)
    "value": "Case Sensitive"
   }
  ]
  $ hg showconfig -Tjson | tail -7
   },
   {
    "name": "*", (glob)
    "source": "*", (glob)
    "value": "*" (glob)
   }
  ]

Test "%unset"

  $ cat >> $HGRCPATH <<EOF
  > [unsettest]
  > local-hgrcpath = should be unset (HGRCPATH)
  > %unset local-hgrcpath
  > 
  > global = should be unset (HGRCPATH)
  > 
  > both = should be unset (HGRCPATH)
  > 
  > set-after-unset = should be unset (HGRCPATH)
  > EOF

  $ cat >> .hg/hgrc <<EOF
  > [unsettest]
  > local-hgrc = should be unset (.hg/hgrc)
  > %unset local-hgrc
  > 
  > %unset global
  > 
  > both = should be unset (.hg/hgrc)
  > %unset both
  > 
  > set-after-unset = should be unset (.hg/hgrc)
  > %unset set-after-unset
  > set-after-unset = should be set (.hg/hgrc)
  > EOF

  $ hg showconfig unsettest
  unsettest.set-after-unset=should be set (.hg/hgrc)

Test exit code when no config matches

  $ hg config Section.idontexist
  [1]

sub-options in [paths] aren't expanded

  $ cat > .hg/hgrc << EOF
  > [paths]
  > foo = ~/foo
  > foo:suboption = ~/foo
  > EOF

  $ hg showconfig paths
  paths.foo:suboption=~/foo
  paths.foo=$TESTTMP/foo