view tests/helpers-testrepo.sh @ 52092:e2311951b63a

tests: raise the default value for the various `devel.sync.*-timeout` configs

These are used in `mercurial.testing.wait_file()` to stall for a file to appear
in the filesystem, and raise an error if the file doesn't show up before the
timeout expires.

The default of 2s was way too low on Windows, especially when running tests in
parallel, and resulted in various timeouts in `test-dirstate-read-race.t`,
`test-dirstate-status-write-race.t`, and `test-clone-stream-revlog-split.t`.
The various `wait-on-file` invocations in the tests are inconsistent, and wait
anywhere from 5s - 20s.  I'm using 20s here because if everything is working,
the timeout won't matter.  Also with the default timeout being raised on Windows
in f4c038081561, both `HGTEST_TIMEOUT_DEFAULT` and `HGTEST_TIMEOUT` are 1440 in
the default case where the timeout is not specified on the command line of the
test runner, so the timing factor that is multipled with the value is 1,
resulting in no changes. (But if someone specified a lower value on the command
line, that would *lower* the timeout period used.)

# In most cases, the mercurial repository can be read by the bundled hg, but
# that isn't always true because third-party extensions may change the store
# format, for example. In which case, the system hg installation is used.
#
# We want to use the hg version being tested when interacting with the test
# repository, and the system hg when interacting with the mercurial source code
# repository.
#
# The mercurial source repository was typically orignally cloned with the
# system mercurial installation, and may require extensions or settings from
# the system installation.

if [ -n "$HGTESTEXTRAEXTENSIONS" ]; then
    for extension in $HGTESTEXTRAEXTENSIONS; do
        extraoptions="$extraoptions --config extensions.$extension=!"
    done
fi

syshg () {
    (
        syshgenv
        exec hg "$@"
    )
}

# Revert the environment so that running "hg" runs the system hg
# rather than the test hg installation.
syshgenv () {
    . "$HGTEST_RESTOREENV"
    HGPLAIN=1
    export HGPLAIN
    if [ -n "$HGTEST_BASE_HGMODULEPOLICY" ]; then
        HGMODULEPOLICY="$HGTEST_BASE_HGMODULEPOLICY"
    else
        unset HGMODULEPOLICY
    fi
    export HGMODULEPOLICY
}

# The test-repo is a live hg repository which may have evolution markers
# created, e.g. when a ~/.hgrc enabled evolution.
#
# Tests may be run using a custom HGRCPATH, which do not enable evolution
# markers by default.
#
# If test-repo includes evolution markers, and we do not enable evolution
# markers, hg will occasionally complain when it notices them, which disrupts
# tests resulting in sporadic failures.
#
# Since we aren't performing any write operations on the test-repo, there's
# no harm in telling hg that we support evolution markers, which is what the
# following lines for the hgrc file do:
cat >> "$HGRCPATH" << EOF
[experimental]
evolution = createmarkers
EOF

# Use the system hg command if the bundled hg can't read the repository with
# no warning nor error.
if [ -n "`hg id -R "$TESTDIR/.." 2>&1 >/dev/null`" ]; then
    testrepohg() {
        syshg "$@"
    }
    testrepohgenv() {
        syshgenv "$@"
    }
else
    testrepohg() {
        hg $extraoptions "$@"
    }
    testrepohgenv() {
        :
    }
fi