view tests/test-exchange-obsmarkers-case-B1.t @ 46607:e9901d01d135

revlog: add a mechanism to verify expected file position before appending

If someone uses `hg debuglocks`, or some non-hg process writes to the .hg
directory without respecting the locks, or if the repo's on a networked
filesystem, it's possible for the revlog code to write out corrupted data.

The form of this corruption can vary depending on what data was written and how
that happened. We are in the "networked filesystem" case (though I've had users
also do this to themselves with the "`hg debuglocks`" scenario), and most often
see this with the changelog. What ends up happening is we produce two items
(let's call them rev1 and rev2) in the .i file that have the same linkrev,
baserev, and offset into the .d file, while the data in the .d file is appended
properly. rev2's compressed_size is accurate for rev2, but when we go to
decompress the data in the .d file, we use the offset that's recorded in the
index file, which is the same as rev1, and attempt to decompress
rev2.compressed_size bytes of rev1's data. This usually does not succeed. :)

When using inline data, this also fails, though I haven't investigated why too
closely. This shows up as a "patch decode" error. I believe what's happening
there is that we're basically ignoring the offset field, getting the data
properly, but since baserev != rev, it thinks this is a delta based on rev
(instead of a full text) and can't actually apply it as such.

For now, I'm going to make this an optional component and default it to entirely
off. I may increase the default severity of this in the future, once I've
enabled it for my users and we gain more experience with it. Luckily, most of my
users have a versioned filesystem and can roll back to before the corruption has
been written, it's just a hassle to do so and not everyone knows how (so it's a
support burden). Users on other filesystems will not have that luxury, and this
can cause them to have a corrupted repository that they are unlikely to know how
to resolve, and they'll see this as a data-loss event. Refusing to create the
corruption is a much better user experience.

This mechanism is not perfect. There may be false-negatives (racy writes that
are not detected). There should not be any false-positives (non-racy writes that
are detected as such). This is not a mechanism that makes putting a repo on a
networked filesystem "safe" or "supported", just *less* likely to cause
corruption.

Differential Revision: https://phab.mercurial-scm.org/D9952

============================================
Testing obsolescence markers push: Cases B.1
============================================

Mercurial pushes obsolescences markers relevant to the "pushed-set", the set of
all changesets that requested to be "in sync" after the push (even if they are
already on both side).

This test belongs to a series of tests checking such set is properly computed
and applied. This does not tests "obsmarkers" discovery capabilities.

Category B: pruning case
TestCase 1: Prune on non-targeted common changeset

B.1 Prune on non-targeted common changeset
==========================================

.. {{{
..     ⊗ B
..     |
..     ◕ A
..     |
..     ● O
.. }}}
..
.. Marker exist from:
..
..  * B (prune)
..
.. Command runs:
..
..  * hg push -r O
..
.. Expected exclude:
..
..  * B (prune)

Setup
-----

  $ . $TESTDIR/testlib/exchange-obsmarker-util.sh

Initial

  $ setuprepos B.1
  creating test repo for test case B.1
  - pulldest
  - main
  - pushdest
  cd into `main` and proceed with env setup
  $ cd main
  $ mkcommit A
  $ mkcommit B

make both changeset known in remote

  $ hg push -qf ../pushdest
  $ hg push -qf ../pulldest

create prune marker

  $ hg prune -qd '0 0' .
  $ hg log -G --hidden
  x  f6fbb35d8ac9 (draft): B
  |
  @  f5bc6836db60 (draft): A
  |
  o  a9bdc8b26820 (public): O
  
  $ inspect_obsmarkers
  obsstore content
  ================
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  $ cd ..
  $ cd ..

Actual Test
-----------

  $ dotest B.1 O
  ## Running testcase B.1
  # testing echange of "O" (a9bdc8b26820)
  ## initial state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pushing "O" from main to pushdest
  pushing to pushdest
  searching for changes
  no changes found
  ## post push state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest
  ## pulling "a9bdc8b26820" from main into pulldest
  pulling from main
  no changes found
  ## post pull state
  # obstore: main
  f6fbb35d8ac958bbe70035e4c789c18471cdc0af 0 {f5bc6836db60e308a17ba08bf050154ba9c4fad7} (Thu Jan 01 00:00:00 1970 +0000) {'user': 'test'}
  # obstore: pushdest
  # obstore: pulldest