addremove: add back forgotten files (BC) After running "hg forget README && hg addremove", README will still be reported as removed, while "hg forget README && hg add README" adds it back so it gets reported as clean. It seems like they should behave the same. Furthermore, it seems like no files should remain untracked after 'hg addremove && hg commit' (or 'hg commit -A'). For these reasons, change the behavior of addremove so it does add forgotten files back. The problem is with scmutil._interestingfiles(), which reports the file as removed, so scmutil.addremove() does not add it. Fix by teaching _interestingfiles() to report forgotten files separately from removed files and make addremove() add forgotten files back. However, do not treat forgotten files as sources for rename detection. Note that since removed and forgotten files are treated the same before this change, forgotten files were considered sources for rename detection. Also update the other caller, marktouched(), in the same way as addremove().

add: add back forgotten files even when not matching exactly (BC) I accidentally did 'hg forget .' and tried to undo the operation with 'hg add .'. I expected the files to be reported as either modified or clean, but they were still reported as removed. It turns out that forgotten files are only added back if they are listed explicitly, as shown by the following two invocations. This makes it hard to recover from the mistake of forgetting a lot of files. $ hg forget README && hg add README && hg status -A README C README $ hg forget README && hg add . && hg status -A README R README The problem lies in cmdutil.add(). That method checks that the file isn't already tracked before adding it, but it does so by checking the dirstate, which does have an entry for forgotten files (state 'r'). We should instead be checking whether the file exists in the workingctx. The workingctx is also what we later call add() on, and that method takes care of transforming the add() into a normallookup() on the dirstate. Since we're changing repo.dirstate into wctx, let's also change repo.walk into wctx.walk for consistency (repo.walk calls wctx.walk, so we're simply inlining the call).

context.status: explain "caching reasons" more fully Where we "load earliest manifest first for caching reasons", elaborate on what "caching reasons" refers to. Text provided by Matt in http://thread.gmane.org/gmane.comp.version-control.mercurial.devel/73235/focus=73578.

localrepo: rename revlog.maxchainlen to format.maxchainlen This is more consistent with other option names, as spotted by Pierre-Yves. Thanks!

revlog: add config variable for limiting delta-chain length The current heuristic for deciding between storing delta and full texts is based on ratio of (sizeofdeltas)/(sizeoffulltext). In some cases (for example a manifest for ahuge repo) this approach can result in extremely long delta chains (~30,000) which are very slow to read. (In the case of a manifest ~500ms are added to every hg command because of that). This commit introduces "revlog.maxchainlength" configuration variable that will limit delta chain length.

debugrevlog: fix computing chain length in debugrevlog -d The chain length was computed correctly only when generaldelta feature was enabled. Now it's fixed. When generaldelta is disabled the base revision in revlog index is not the revision we have delta against - it's always previous revision. Instead of incorrect chainbaseandlen in command.py we are now using two single-responsibility functions in revlog.py: - chainbase(rev) - chainlen(rev) Only chainlen(rev) was missing so it was written to mimic the way the chain of deltas is actually found during file reconstruction.

transaction: factorise append-only file registration The addition is done in two different places but differs slightly. We factorise this addition to ensure it is consistent in all places.

transaction: document `tr.add`

transaction: drop backupentries logic from startgroup and endgroup The `startgroup` and `endgroup` methods are used in a very specific context to wrap a very specific operation (revlog truncation). It does not make sense to perform any other operations during such a "group" (eg:file backup). There is currently no user of backupfile during a "group" so we drop the group-specific code and restrict authorized operations during "group".

transaction: document startgroup and endgroup These enigmatic methods are only used in repair. We document them to clarify there purpose and user.